Specifications:
Input voltage: 6V to 28V (2S - 6S) VBat
Power Output:5V for Camera @ 0.5A max
Remote software protocol:SmartAudio V2.0
Output Power:14dBm (25mW) 23dBm (200mW*)
Pit mode:
Activate: press button during powered up.
LED: red
Deactivate:
press button during powered up.
LED: blue
( red & blue when unlocked)
Pit mode-> flight mode:
After boot up, press button for 8sec
Channels:
Band A (8ch), B (8ch), E(5ch)
Fatshark 8ch
Race Band 8ch
Low Race Band 8ch **
Power consumption:
25mW: 250mA
200mW: 320mA
Range:Up to 2 km
Video Transmitter
There are categories in the menu, and settings. Pressing the button for 3 seconds will toggle between
categories, pressing it for a short (1 second) press toggles between settings. To enter the menu, hold the
button for 3 seconds. LED colors will signal the state of the menu, for an overview see the following table.
Channel select mode
Enter menu by pressing the button for 3s. Red LED will flash 1 time. Select channels by simple short
presses.
Band select mode
Press button for an additional 3s. Red LED will flash 2 times. Select band by simple short presses.
Unlock & power select mode
(FOR HAM USERS ONLY!) Press button for 20 to 25 seconds. The Red LED will flash 3 times to confirm. You
have unlocked the video transmitter for use with all frequencies (see frequency table below).
NOTE : Unlock only works if you are inside the band selection menu
The power select mode is now accessible. Once unlocked, you can select the power level according to the
table below. To lock the transmitter, go back into band select menu and press the button for 20 to 25
seconds again.
PitMode
While in PitMode you can change channels and set power levels without affecting other pilots signal.
Pit mode function explained HERE
Save and exit
Press button for 3 seconds. Blue LED will turn on, settings are saved and it will exit the menu.
Button menu structure
LED Flash C od es for C h an n el, B an d an d Pow er
The TB S U N IFY PRO 5G 8 signals selected channel, band and pow er levels using a startup sequence of LED
codes. The sam e sequence is also repeated in the m enu to m ake it unified. First the
RED
LED flashes to
indicate the item being show n. O ne flash for channel, tw o flashes for band, three flashes for pow er level.
Subsequently, the
B LU E
LED w ill indicate the value.
R ed LED :
Indicate item - C hannel, band or pow er setting
Blu e LED :
Indicate value
For exam ple, C hannel 6, B and B , Pow er of 500m W , w ill have the follow ing startup LED code:
●
1x
Red
and 6x
Blue
= C hannel, 6
●
2x
Red
and 2x
Blue
= B and, 2 (=B )
●
3x
Red
and 3x
Blue
= Pow er, 3 (= 500m W )
O nce the Video transm itter has successfully booted up, it w ill show a constant
B LU E
for locked state, and a
constant
RED
+
B LU E
for unlocked state.
For reference, see the follow ing m enu table.
Men u Table
R ED LED
B LU E LED
1x
2x
3x
4x
5x
6x
7x
8x
1x
C h an n el
1
2
3
4
5
6
7
8
2x
B an d
A
B
E
A irw ave
Race
Low Race
3x
Pow er Level
25
200
Freq u en cy Table
C h an n el
1
2
3
4
5
6
7
8
B an d A
5865
5845
5825
5805
5785
5765
5745
5725
M H z
B an d B
5733
5752
5771
5790
5809
5828
5847
5866
M H z
B an d E
5705
5685
5665
5645
5885
5905
5925
5945
M H z
A irw ave
5740
5760
5780
5800
5820
5840
5860
5880
M H z
R ace B an d
5658
5695
5732
5769
5806
5843
5880
5917
M H z
Low R ace B an d *
5621
5584
5547
5510
5473
5436
5399
5362
M H z
Pow erLevel
25
200
m W
