gofanco HDBaseT4P-4K Скачать руководство пользователя страница 11

Страница: 11 / 16

EDID Management

EDID is used by the source device to match the video

resolution to the connected display(s). The source device

obtains its EDID from the 1st connected display as default

setting. However, since displays with different capabilities

are often connected to the splitter, the EDID DIP switch

can be used to set the EDID to a fixed value to offer the

best compatiblity accross all connected displays.

Front Panel EDID Switch

L. RES

The Extender/Splitter reads EDID from all

connected displays, and then the source device

will automatically use the EDID from the display

with the lowest resolution

Default

The factory default EDID resolution is 4K@60Hz

H. RES

The Extender/Splitter reads EDID from all

connected displays, and then the source device

will automatically use the EDID from the display

with the highest resolution

Содержание HDBaseT4P-4K

















Результаты поиска

Содержание HDBaseT4P-4K

Отзывы:

Похожие инструкции для HDBaseT4P-4K

Бренды по названию

Популярные бренды

gofanco HDBaseT4P-4K, Руководство пользователя

Результаты поиска

Содержание HDBaseT4P-4K

Отзывы:

Похожие инструкции для HDBaseT4P-4K

Бренды по названию

Популярные бренды