Using the Wide Panel
Pull out the wide panel and place it
over the flash head as shown. The
flash coverage will then be extended
to 14 mm.
●
The catchlight panel will come out
at the same time. Push the
catchlight panel back in.
Low Battery Warning
If the battery power is low, <
> will
appear and blink on the LCD panel.
P l e a s e r e p l a c e t h e b a t t e r y
immediately. When the low battery
indicator is displayed, the ZOOM
can not be adjusted.
C.Fn: Setting Custom Functions
The following table lists the available and unavailable custom
functions of this flash.
ST
AF
BL
AP
ID
ON
OF
ON
OF
10 sec.
OF
ON
ON
OFF
OFF
01-99
Auto sleep
(standby)
AF-assist beam
Backlighting
control
ZOOM display
format
Wireless ID
C
.
Fn
Custom
Functions
Custom Function
Signs
Function
Setting No
.
Settings & Description
ON
OFF
ON
OFF
Off in 10 sec.
Always off
Always lighting
APS format
135 format
Off
Choose any figure from 01-99
1
.
Press the <
ZOOM
> Button for 2 seconds until C.Fn menu is
displayed.
2
.
Turn the Select Dial to select the Custom Functions.
3
.
Press the <
SET
> Button and the Setting No. blinks.
4. Turn the Select Dial to set the desired number. Pressing the
<
SET
> Button will confirm the settings.
5
.
Press the <
ZOOM
> Button to exit.
Protection Function
1. Over-Temperature Protection
●
To avoid overheating and deteriorating the flash head, do not fire
more than 30 continuous flashes in fast succession at 1/1 full
power. After 30 continuous flashes, allow a rest time of at least 10
minutes.
●
If you fire more than 30 continuous flashes and then fire more
flashes in short intervals, the inner over-temperature protection
function may be activated and make the recycling time over 10
seconds. If this occurs, allow a rest time of about 10 minutes, and
the flash unit will then return to normal.
●
When the over-temperature protection is started, is shown on
the LCD display.
Number of flashes that will activate over-temperature protection:
Number of flashes that will activate over-temperature protection in
high-speed sync triggering mode:
Power Output Level
1/1
1/2 +0.7
1/2 +0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
Number of Flashes
30
40
50
60
100
200
300
500
1000
Power Output
1/1
1/2(+0.3,+0.7);
1/4(+0.3,+0.7)
1/8(+0.3,+0.7);
1/16(+0.3,+0.7)
Times
15
20
30
40
Meaning
A failure occurs on the recycling system so that the
flash cannot fire.
Please restart the flash unit. If the problem still exists,
please send this product to a maintenance center.
The voltage on two outlets of the flash tube is too high.
Please send this product to a maintenance center.
There are some errors occurred during the upgrading
process. Please using the correct firmware upgrade
method.
Prompts on LCD Panel
E1
E3
E9
2. Other Protections
The system provides real-time protection to secure the device and
your safety. The following lists prompts for your reference:
●
When pull out the wide panel, the ZOOM will constantly be
14mm. The <ZOOM> button will not work.
- 47 -
- 48 -
