background image

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not 
cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation. 

Any Changes or modifications not expressly approved by the party 
responsible for compliance could void the user's authority to operate 
the equipment. 

Note:

 This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This 
equipment generates uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: 
 

 Reorient or relocate the receiving antenna. 

 

 Increase the separation between the equipment and receiver. 

 

 Connect the equipment into an outlet on a circuit different  

      from that to which the receiver is connected. 
 

 Consult the dealer or an experienced radio/TV technician for 

      help. 

*RF warning:

This equipment complies with FCC radiation exposure limits set 
forth for an uncontrolled environment. 

IC statement:
This device complies with Industry Canada licence-exempt RSS 
standard(s).
Operation is subject to the following two conditions: (1) this device 
may not cause interference, and (2) this device must accept any 
interference, including interference that may cause undesired 
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada 
applicables aux appareils radio exempts de licence. L'exploitation 
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit 
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit 
accepter tout brouillage radioélectrique subi, même si le brouillage 
est susceptible d'en compromettre le fonctionnement.
:
This equipment complies with Industry Canada radiation exposure 
limits set forth for an uncontrolled environment. 
Cet équipement est conforme à l'exposition aux rayonnements 
Industry Canada limites établies pour un environnement non 
contr?lé.

Содержание V1F































Отзывы: