background image

PART #

 

DESCRIPTION

 

43-810-200

 

PRESSURE REGULATOR ASSEMBLY

 

Complete pressure regulator (unassembled)

 

43-810-250

 

PRESSURE REGULATOR REBUILD KIT:

 

Upper Metal, 

Spring, Under Metal, Packing, Spindle Guide, Oil Seal, Box, 
Spindle, Ball Valve, O-Ring, Ball Valve Seat  
(ref# 113-119, 121-124)

 

43-810-325

 

PACKING REPAIR KIT: 9 V Packings, 3 Crown Nuts, 3 
Grease Rings,  3 Water Stopping Rings, 3 Grease Packings 
(ref# 43-48)

 

43-810-350 

(ref# 53)

 

VALVE REPAIR KIT: 6 Valves, 6 Seals(Valve Box, Spring 
Valve, Valve Flat, Valve Seat, Valve Ring, Valve Seal)

 

43-810-380

 

PUMP REBUILD KIT:

 

3 Crown Nuts, 3 Grease Rings, 3 V-

Packing, 3 Water Stopping Rings, 3 Grease Packing, 9 Pack-
ing, 6 Valves, 6 Seals (ref# 43-48, 53)

 

1.  Spray gun tip too large or worn 
2.  Suction filter clogged 
3.  Loose suction line connection 
4.  Malfunctioning pressure gauge 
5.  Malfunctioning pressure regula-

tor 

6.  Worn pump suction and dis-

charge valves 

7.  Over speeding the pump 
8.  Suction line too small 

9.  Pulsation dampening chamber 

full of water 

10.  Worn pump valve chamber 
11.  Foreign object in suction line 
12.  Plunger packing worn 
13.  Pump drive belts loose 
14.  Pressure regulator by-pass 

valve open 

15.  Suction line valve closed 

16. 

Drive pulley spinning on pump 

TROUBLESHOOTING REFERENCE NUMBERS 

REPAIR KITS 

Page 6 

Содержание P10













Отзывы: