background image

WARRANTY 

 

GNC Industries, Inc., products are warranted by GNC Industries, Inc.. GNC Indus-
tries, Inc. will repair or replace (at GNC Industries, Inc.’s option) any part or as-
sembly, free of charge, if that part or assembly fails within twenty four months (2 
years) from the date of purchase, provided the failure is due to an unmistakable 
defect in material or workmanship.  

 

No allowance will be made for consequential damage, labor or expenses incurred 
as the results of a proven defect.  In no event will GNC Industries, Inc. be liable for 
any loss of profits or other consequential damages, even if GNC Industries, Inc. 
has been advised of the possibility of such damages. 

 
GNC Industries, Inc. assumes no responsibility for accidents or injuries resulting 
from maintenance or adjustment of product while product is in operation. 

 
Since GNC Industries, Inc. has no control over the operational techniques or 
chemicals used, GNC Industries, Inc. assumes no liability for the consequences of 
the use or misuse of any equipment by the Purchaser his employees or others. 

 
Maximum operation speed and pressure is specified in individual and applicable 
instructions. 

 
GNC Industries, Inc. reserves the right to improve any product without being obli-
gated to provide that change on equipment sold and/or shipped prior to the prod-
uct change. 

Modification of equipment voids all warranties written or implied  

Page 1 

Содержание P10













Отзывы: