GMP PROTOPIC-540 QUATRO SLIT Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 51

background image

How to laminate

1. How to load film

☞ Composition of Film installing devices

① Film Shaft : The film shaft is used to load a laminating roll films.

② Film Shaft Holder Fixing Pin. : Film Shaft Holder Fixing Pin is used to fix the Film shaft Holder.

③ Film Shaft Holder : The Film Shaft Holder is used to prevent the Film Shaft from moving

④ Film Core : Film Core is used to fix the laminating roll films.

※ How to install film

① Remove the Film Shaft Holder Fixing Pin and pull the Film Shaft Holder

② remove any side of Film Core by using the Film Shaft Holder Fixing Pin

③ Insert or Remove film roll into or from Film Shaft. (Please refer to the Drawing 1)

④ Insert a film roll into the film shaft after the holder fixing pin is removed.

⑤ Tighten the Film core fixing bolt after film is loaded.

Remarks : When doing "Single side lamination" please use 5~10mm narrower width films than substrate to prevent

the contamination on roller / of cutting error

Remarks : When doing "Double side lamination" Please use the same width

for the upper and lower films to to prevent the contamination on roller.

Drawing 1. The Direction of the films when loading

②

①

③

④

Glue
Side

Glossy
Side

Glue

[Upper Films]

[Lower Films]

28/51

«
...
26
27
28
29
30
...
»

Содержание PROTOPIC-540 QUATRO SLIT




















































Отзывы:

Нет отзывов

Похожие инструкции для PROTOPIC-540 QUATRO SLIT

Бренд: VALUELAM Страницы: 16

Бренд: Tamerica Страницы: 9

Бренд: Drytac Страницы: 25

Бренд: GBC Страницы: 8

Бренд: Lami Corporation Страницы: 18

Бренд: Opus Страницы: 15

Бренд: Mega Electronics Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды