background image

 

D1049 

- SIL 3 Digital Output Driver NE Loads Bus Powered 

G.M. International ISM0097-9 

Parameters Table 

In the system safety analysis, always check the Hazardous Area/Hazardous Locations devices to conform with the related system documentation, if the device is Intrinsically Safe check 
its suitability for the Hazardous Area/Hazardous Locations and gas group encountered and that its maximum allowable voltage, current, power (Ui/Vmax, Ii/Imax, Pi/Pi) are not exceeded 
by the safety parameters (Uo/Voc, Io/Isc, Po/Po) of the D1049 Associated Apparatus connected to it. Also consider the maximum operating temperature of the field device, check that 
added connecting cable and field device capacitance and inductance do not exceed the limits (Co/Ca, Lo/La, Lo/Ro) given in the Associated Apparatus parameters for the effective gas 
group. See parameters on

 

enclosure side and the ones indicated in the table below: 

 

Must 

be 

Hazardous Area/ 

Hazardous Locations 

Device Parameters 

D1049 Associated 

Apparatus Parameters 

Uo / Voc = 24.9 V 

Ui / Vmax 

D1049 Terminals 

Out A 

13 - 16 

Out B 

14 - 16 

 

Must 

be 

Hazardous Area/ 

Hazardous Locations 

Cable Parameters 

D1049 Terminals 

D1049 Associated 

Apparatus Parameters 

Ci / Ci  C cable 

 

Li / Li L cable 

 

Lo / La = 1.65 mH 
Lo / La = 6.63 mH 
Lo / La = 13.2 mH 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Lo / La = 2.9 mH 

Lo / La = 11.8 mH 
Lo / La = 23.6 mH 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Lo / La = 4.19 mH 
Lo / La = 16.7 mH 
Lo / La = 33.5 mH 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Out C 

15 - 16 

Io / Isc = 147 mA 

Ii/ Imax 

Out A 

13 - 16 

Out B 

14 - 16 

 

Io / Isc = 110 mA 

Out C 

15 - 16 

Io / Isc = 93 mA 

Po / Po = 907 mW 

Pi / Pi 

Out A 

13 - 16 

Out B 

14 - 16 

 

Po / Po = 681 mW 

Out C 

15 - 16 

Po / Po = 571 mW 

Out A 

13 - 16 

Out B 

14 - 16 

Out C 

15 - 16 

Co / Ca = 112 nF 
Co / Ca = 850 nF 

Co / Ca = 3.01 µF 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Li / Ri device and 

L cable / R cable 

 

Lo / Ro = 39.2 µH/

 

Lo / Ro = 156.8 µH/

 

Lo / Ro = 313.6 µH/

 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Lo / Ro = 52.2 µH/

 

Lo / Ro = 208.9 µH/

 

Lo / Ro = 417.8 µH/

 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Lo / Ro = 62.3 µH/

 

Lo / Ro = 249.4 µH/

 

Lo / Ro = 498.9 µH/

 

(IIB-C) 
(IIA-D) 

(IIC-A, B) 

Out A 

13 - 16 

Out B 

14 - 16 

Out C 

15 - 16 

NOTE for USA and Canada: 

IIC equal to Gas Groups A, B, C, D, E, F and G, 
IIB equal to Gas Groups C, D, E, F and G, 

IIA equal to Gas Groups D, E, F and G 

Out A 

13 - 16 

15 - 16 

Out B 
Out C 

14 - 16 

Co / Ca = 4.35 µF 
Co / Ca = 0.86 µF 

(I) 

(IIIC) 

Lo / La = 21.78 mH 

Lo / La = 6.63 mH 

(I) 

(IIIC) 

Lo / La = 40.36 mH 

Lo / La = 12.3 mH 

(I) 

(IIIC) 

Lo / La = 55.09 mH 

Lo / La = 16.7 mH 

(I) 

(IIIC) 

Lo / Ro = 514.6 µH/

 

Lo / Ro = 156.8 µH/

 

(I) 

(IIIC) 

Lo / Ro = 700.6 µH/

 

Lo / Ro = 213.5 µH/

 

(I) 

(IIIC) 

Lo / Ro = 818.5 µH/

 

Lo / Ro = 249.4 µH/

 

(I) 

(IIIC) 

Содержание D1049S










Отзывы: