GM INSTRUMENTS NR6 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 34

background image

Rhinomanometer NR6

NR6 User

’s

Manual V 16 14/02/2020 P3 of 34

NR6 RHINOMANOMETER SAFETY INFORMATION

Read this Operating Manual before attempting to use the
Instrument.

WARNINGS

This  Instrument  is  for  indoor  use,  in  a  professional  healthcare  facility  only  and  used  as
described in this manual.

It should not be used near active High Frequency Surgical Equipment nor in the RF shielded
room  of  an  ME  system  for  magnetic  resonance  imaging,  where  the  intensity  of  Electro
Magnetic disturbances are high.

Use  of  this  equipment  adjacent  to,  or  stacked  with,  other  equipment  should  be  avoided
because  it  could  result  in  improper  operation.  If  necessary,  this  equipment  and  the  other
equipment should be observed to verify they are operating normally.

Should the NR6 be affected by external influences such as those described above, it may not
perform correctly. Determination of correct operation can be easily assessed as described in
page 12 of this manual.

Use  of  accessories,  transducers  and  cables  other  than  those  specified  or  provided  by  the
manufacturer  of  this  equipment  could  result  in  increased  electromagnetic  emissions  or
decreased electromagnetic immunity of this equipment and result in improper operation.

Portable  RF  communications  equipment  (including  peripherals  such  as  antenna  cables  and
external  antennas) should  be used  no  closer  than  30  cm  (12  inches) to any part of  the  ME
SYSTEM,  including  cables  specified  by  the  manufacturer.  Otherwise,  degradation  of  the
performance of this equipment could result.

This unit is a PC connected product. It is advisable not to touch the patient while using the
equipment.

The equipment should be positioned in such a way that it can be easily disconnected from a
mains  powered  PC.  The  operation  of  the  system  can  be  safely  terminated  by  switching  off
the PC, or removing the USB cable between the PC and NR6.

Applied  Parts.  The  applied  parts  consist  of  single-use  foam  inserts,  microfoam  tape
(hypoallergenic  elastic),  tip  connectors  (Nylon),  anterior  or  posterior  tubing  (Silicone),  masks
(single-use /or  reusable silicone)  connected to an antiviral  filter, flowheads  and  silicon rubber
tubing.

The  system  must  not  be  used  in  the  presence  of  flammable  gases  or  in  an  environment,
which is susceptible to explosions.   (Beware of oxygen, dust and anaesthetic gases)

«
1
2
3
4
5
...
»

Содержание NR6



































Отзывы:

Нет отзывов

Похожие инструкции для NR6

Бренд: Van Walt Страницы: 6

Бренд: zebris Страницы: 42

Бренд: jenway Страницы: 20

Бренд: Badger Meter Страницы: 47

Бренд: Maico Страницы: 27

Бренд: Magnescale Страницы: 14

Бренд: Weller Страницы: 9

Бренд: OBDPROG Страницы: 8

Бренд: ZHYQ Страницы: 6

Бренд: Hama Страницы: 16

Бренд: Schneeberger Страницы: 35

Бренд: ILX Lightwave Страницы: 126

Бренд: Johnson & Associates Страницы: 33

Бренд: PCE Health and Fitness Страницы: 11

SensoControl Serviceman SCM-150 Series

Бренд: Parker Страницы: 39

Бренд: Vega Страницы: 52

Бренд: IS Technologies Страницы: 21

Бренд: Mityvac Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды