Glow-worm Compact 24c-AS/1 страница 50 Скачать руководство пользователя

Страница: 50 / 60

Installation and maintenance instructions Compact 0020313973_01

Code/meaning

Possible cause

Measure

F.68

Fault: Unstable flame signal

Air in the gas supply (e.g. dur-
ing initial start-up)

▶

Reset the unit once.

Gas flow pressure too low

▶

Check the gas flow pressure.

Incorrect air ratio

▶

Check the CO

content at the flue gas analysis point.

Incorrect flue gas recirculation

▶

Check the flue gas recirculation.

Condensate discharge pipe
blocked

▶

Check the condensate discharge pipe.

F.70

Invalid device specific number
(DSN)

Device Specific Number not
set/is incorrect

▶

Set the correct Device Specific Number.

F.71

Flow temperature sensor fault

The flow temperature sensor
signals a constant value

▶

Check the positioning of the flow temperature sensor.

Flow temperature sensor in the
incorrect position

▶

Check the positioning of the flow temperature sensor.

Flow temperature sensor de-
fective

▶

Replace the flow temperature sensor.

F.72

Fault: Return temperature
sensor

Flow temperature sensor de-
fective

▶

Replace the flow temperature sensor.

Return temperature sensor de-
fective

▶

Replace the return temperature sensor.

F.73

Water pressure sensor signal in
the wrong range (too low)

Short circuit in the cable har-
ness

▶

Check the cable harness.

Interruption in the cable harness

▶

Check the cable harness.

Water pressure sensor defect-
ive

▶

Replace the water pressure sensor.

F.74

Water pressure sensor signal
outside correct range (too high)

Short circuit in the cable har-
ness

▶

Check the cable harness.

Interruption in the cable harness

▶

Check the cable harness.

Water pressure sensor defect-
ive

▶

Replace the water pressure sensor.

F.76

Fault: Thermal cut-out

Defective thermal fuse

▶

Check the heat exchanger for leakages. If the heat exchanger
has no leaks, bypass the thermal fuse. If you can then start
the product, replace the thermal fuse.

F.77

Fault: Flue non-return
flap/condensate pump

No feedback from the flue non-
return flap or the feedback is
incorrect

▶

Check that the flue non-return flap functions correctly.

Flue non-return flap defective

▶

Replace the flue non-return flap.

Condensate pump defective

▶

Replace the condensate pump.

F.78

Interruption: Domestic hot water
outlet temperature sensor with
external control

NTC sensor defective

▶

Replace the NTC sensor.

F.83

Fault: NTC temperature fluctu-
ation

System pressure too low

▶

Check the system pressure.

Flow temperature sensor: No
contact

▶

Check whether the flow temperature sensor is lying against the
flow pipe correctly.

Return temperature sensor: No
contact

▶

Check whether the return temperature sensor is lying against
the return pipe correctly.

Insufficient/no water in the
product.

▶

Fill the heating installation. (

→

Page 29)

F.84

NTC temperature difference is
implausible

Flow temperature sensor in-
stalled incorrectly

▶

Check whether the flow temperature sensor has been installed
correctly.

Return temperature sensor in-
stalled incorrectly

▶

Check whether the return temperature sensor has been in-
stalled correctly.

Flow and return temperature
sensors inverted

▶

Check whether the flow and return temperature sensor has
been installed correctly.

F.85

Flow and return temperature
sensors have been installed
incorrectly (inverted)

Flow/return temperature
sensors have been installed on
the same pipe/wrong pipe

▶

Check that the flow and return temperature sensors have been
installed on the correct pipe.

F.86

External safety shutdown

Limit thermostat settings incor-
rect

▶

Check the limit thermostat settings.

Содержание Compact 24c-AS/1





























































Результаты поиска

Содержание Compact 24c-AS/1

Отзывы:

Похожие инструкции для Compact 24c-AS/1

Бренды по названию

Популярные бренды

Glow-worm Compact 24c-AS/1, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Compact 24c-AS/1

Отзывы:

Похожие инструкции для Compact 24c-AS/1

Бренды по названию

Популярные бренды