background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

6

Electrical Supply Failure

The boiler will not work without an electrical supply.
Normal operation of the boiler should resume when the electri-

cal supply is restored. 
Reset any external controls, to resume normal operation of the 

central heating.
If the boiler does not resume normal operation turn the mode 

knob on   position. If the boiler does not resume normal op-

eration after this call your Installation/Servicing company. 

Overheating safety

In the event of the boiler overheating the safety devices will 

cause a safety shutdown. If this happens, turn the mode knob 

on   position.

Safety Discharge Valve

A  safety  discharge  valve  and  discharge  pipe  is  fi tted  to  the 

boiler.  This valve must not be touched.  Should there be any 

discharge from the pipe, isolate the boiler electrical supply and 

call  your  installer  or  Glow-worm’s  own  service  organisation 

using the telephone number on the inside front cover of this 

booklet.

Appliance Safety Devices

Frost protection

The appliance has a built in frost protection device that protects 

the boiler from freezing. With the gas and electric supplies ON 

and irrespective of any room thermostat setting, the frost pro-

tection device will operate the pump when the temperature of 

the boiler water falls below 5°C. 
The burner will switch off when the temperature reaches 30°C.

Condensate Drain Blockage

As a safety feature the boiler will stop working if the condensate 

drain becomes blocked. During freezing conditions this may be 

due to the forming of ice in the condense drain external to the 

house.  Release an ice blockage by the use of warm cloths on 

the pipe.  The boiler should then restart.  Contact your installa-

tion/servicing company if the fault persists.

Maintenance and Servicing

Maintenance and Servicing

To ensure the continued effi cient and safe operation of the ap-

pliance it is recommended that it is checked and serviced as 

necessary at regular intervals.  The frequency of servicing will 

depend upon the particular installation conditions and usage.
If this appliance is installed in a rented property there is a duty 

of care imposed on the owner of the property by the current is-

sue of the Gas Safety (Installation and Use) Regulations, Sec-

tion 35.
Servicing/maintenance should be carried out by a 

competent 

person

 in accordance with the rules in force in the countries 

of destination.
To  obtain  service,  please  call  your  installer  or  Glow-worm’s 

own service organisation using the telephone number on the 

inside front cover of this literature.
Please  be  advised  that  the  ‘Benchmark’  logbook,  located  at 

back of literature, should be completed by the installation engi-

neer on completion of commissioning and servicing.

Spare Parts

Remember, when replacing a part on this appliance, use only 

spare parts that you can be assured conform to the safety and 

performance specifi cation that we require.  Do not use recon-

ditioned or copy parts that have not been clearly authorised by 

Glow-worm.
If a part is required contact Glow-worm’s own service organisa-

tion using the telephone number on the inside front cover of 

this booklet.
Please quote the name of the appliance, this infomation will be 

on the name badge on the front of the appliance.
If in doubt seek advice from the local gas company or Glow-

worm’s own service organisation using the telephone number 

on the inside front cover of this booklet.

Содержание Betacom 24





















































Отзывы: