manualshive.com logo in svg

Global Ultimate, Инструкции по окончательной сборке, Страница: 2 / 32

Поделиться
Скачать
Global Ultimate Скачать руководство пользователя страница 2

2

TABLE OF CONTENTS

To make your modeling experience totally enjoyable, we recommend that you get experienced, knowledgable
help with assembly and during your first flights.  Your local hobby shop has information about flying clubs in
your area whose membership includes qualified instructors.  You can also contact the AMA at the address below.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN.  47302-9252

(800) 435-9262

www.modelaircraft.org

Global guarantees this kit to be free from defects in both material and workmanship, at the date of purchase.  This does
not cover any components parts damaged by use, misuse or modification.  In no case shall Global's liability exceed the
original cost of the purchased kit.

In that Global has no control over the final assembly or material used for final assembly, no liability shall be assumed
for any damage resulting from the use by the user of the final user-assembled product.  By the act of using the final
user-assembled product, the user accepts all resulting liability.

Kit Contents....................................................2
Additional Items Required...............................3
Tools and Supplies Needed..............................3
Field Support Equipment Needed.....................3
Metric Conversion Chart..................................3
Bottom Wing Mounting...................................4

Align the Bottom Wing.............................4
Installing the Blind Nuts...........................4
Installing the Wing Bolt Doubler...............5
Installing the Wing....................................5

Horizontal Stabilizer Mounting........................5

Align the Horizontal Stabilizer..................5
Mounting the Horizontal Stabilizer............6

Vertical Stabilizer Mounting...........................7

Align the Vertical Stabilizer......................7
Mounting the Vertical Stabilizer................7

Top Wing Mounting........................................7

Align the Top Wing...................................7
Installing the Interplane Struts...................8
Mounting the Top Wing............................9

Control Surface Installation..............................9

Hinge the Elevator Halves.........................9
Install the Tail Wheel Assembly................9
Hinge the Rudder....................................10
Install the Tail Wheel..............................11
Hinge the Bottom Wing Ailerons............11
Hinge the Top Wing Ailerons..................11

Engine Mounting...........................................12

Mounting Engine to Motor Mount...........12
Aligning the Motor Mount.......................12
Mounting the Engine to Firewall..............13

Fuel Tank......................................................13

Fuel Tank Assembly................................13
Fuel Tank Installation..............................14

Throttle Linkage............................................14

Installing the Throttle Linkage.................14

Main Landing Gear........................................14

Installing the Gear Bracket.......................14
Installing the Wheel Pants........................15
Adjusting the Wheel Pants.......................15

Aileron Servo................................................16

Installing the Aileron Servo.....................16
Installing the Aileron Linkage..................16

Radio Installation...........................................17

Installing the Servo Tray..........................17
Installing the Servos.................................17
Installing the Receiver and Battery...........17
Installing the Switch................................17

Throttle Linkage............................................18

Installing the Throttle Connector..............18

Rudder Pushrod..............................................18

Installing the Rudder Control Horn..........18
Installing the Rudder Pushrod..................19

Elevator Pushrod............................................20

Installing the Elevator Control Horns.......20
Installing the Pushrod Joiner....................20
Installing the Elevator Pushrod.................20

Aileron Links.................................................21

Installing the Control Horns.....................21
Installing the Aileron Links......................22

Canopy..........................................................22

Trimming the Canopy..............................22
Mounting the Canopy..............................22

Cowling.........................................................22

Mounting the Cowl..................................22

Balancing.......................................................24

Lateral Balance........................................24

Control Throws..............................................24
Flying............................................................25
Notes.............................................................25
Trim Chart.....................................................26

Содержание Ultimate

































Отзывы:

Нет отзывов