background image

MAINTENANCE

JUNO-NET

2.9 LOGBOOK

In accordance with EN54 part 14, it is the user's responsibility to maintain a logbook and to record all
events resulting from or affecting the system. The logbook should be kept in a place accessible to
authorised persons (preferably near the control panel).

One or more identifiable individuals should be appointed to oversee or carry out all entries in the logbook.
The names of these persons (and any changes of responsible person) should be recorded.

All events should be properly recorded (events include real and false fire alarms, faults, pre-alarm
warnings, tests, temporary disconnections and service visits). A brief note of any work carried out or
outstanding should be made.

Sample pages of the logbook are provided here and can be photocopied to produce a logbook that
conforms to EN54-14. The sample below is for the reference data (e.g. the name of the responsible
person), whilst the sample on the next page is for entry of event data.

REFERENCE DATA

Name and address:

Responsible person:

Date:_________________________

________________________ Date:_________________________

________________________ Date:_________________________

________________________ Date:_________________________

The system was installed by:_______________________________________________

and is maintained under contract by:________________________________________

_______________________________until:___________________________________

Telephone number:____________________________________

should be contacted if service is required.

27

OPERATION & MAINTENANCE MANUAL
REVISION 0.7a
16-04-2004

Содержание JUNO-NET






























Отзывы: