background image

globalindustrial.ca

Distribucion Industrial Globales S DE RL DE CF

Instruction Manual

Manual de Instrucciones

Manuel d'instruction

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

México: 01.800.681.6940

Service à la clientèle

Canada: 888-645-2986

1

Outdoor Drinking Fountain w/ Bottle Filling Station

Models 761216, 761216BK,

761216BL & 761216GN

•   All installation work must be performed by authorized

service personnel.

•   Two or more people are recommended to lift and

install the unit.

•   To avoid the risk of property damage and/or personal

injury, ensure the mounting surface is adequate to support

400 lbs.

•   Check local codes for plumbing requirements prior

to installation.

•   Refer to Rough-In Guide (page 4) prior to installation.

•   Thoroughly flush all water supply lines of all foreign

matter before connecting to the fixture.

•   Check for any leaks before use.

•   DO NOT attempt to repair or replace any part of this

fountain unless it is specifically recommended in this

manual. All other services should be referred to a

qualified technician.

•   For use with clean, clear potable drinking water only.

•   Shut-off water supply during installation to reduce the

risk of water damage.

•   Freezing Caution: Before freezing temperatures occur,

refer to the Draining and W

interization section of this

manual (page 11) for proper preparation.

•   Installation of a trap on the water drain line may be

necessary; remove trap before winterization draining.

•   Failure to follow safety warnings and/or

installation instructions will void warranty.

WARNING

Note:

 This unit is designed to be installed on the surface of an existing or new concrete slab.

Included are the necessary vandal-resistant stainless steel bolts and washers needed

to anchor this unit. Installer must provide a 1-1/2” PVC drain line (if applicable) and water supply

line. All connections are made inside the item through the access doors, as shown in the drawings.

It is recommended to install a shut-off valve (not included) on the water supply. 

Содержание 761216












Отзывы: