Index
Table of Contents
Chapter 1 Introduction ...........................................................1
1.1 Copyright Notice .................................................................. 2
1.2 About this User's Manual .......................................................2
1.3 Warning ...............................................................................2
1.4 Replacing the lithium battery .................................................3
1.5 Technical Support ................................................................ 3
1.6 Warranty ............................................................................. 4
1.7 Packing list .......................................................................... 5
1.8 Cable Kit ............................................................................. 5
1.9 Ordering Information ..........................................................
6
1.10 Specification ......................................................................7
1.11 Board dimensions .............................................................. 8
Chapter 2 Installation ............................................................
9
2.1 Board layout ........................................................................ 10
2.2 Jumpers and Connectors ...................................................... 11
Chapter 3 BIOS ......................................................................
25
3.1 BIOS Introduction ................................................................ 26
3.2 BIOS Setup ......................................................................... 26
3.3 Standard CMOS Features ..................................................... 27
3.4 Advanced BIOS Features ..................................................... 29
3.5 Advanced Chipset Features .................................................. 33
3.6 Integrated Peripherals ..........................................................36
3.8 PNP/PCI Configurations ....................................................... 45
3.9 PC Health Status ................................................................. 46
3.10 Frequency/Voltage Control ................................................. 47
3.12 Set Password .....................................................................48
3.13 Save & Exit Setup ...............................................................49
3.14 Exit Without Saving ............................................................ 49
3.15 BIOS memory map ............................................................. 50
3.16 Award BIOS Post Codes ......................................................50
Chapter 4 Appendix ...............................................................
56
4.1 I/O Map ............................................................................... 57
4.2 IRQ Map ..............................................................................58
4.3 Example of Watch Dog codes ................................................ 58
3.7 Power Management Setup ................................................... 42
3.11 Load Optimized Defaults ..................................................... 47
Installation
Jumpers
JVLCD1: LCD Panel Voltage Select (15)
The voltage of LCD panel could be selected by JVLCD in +V or +3.3V.
Connector type: 2.4mm pitch x3 pin header
Pin
Voltage
-2
+V
2
3
1
2-3
+3.3V (Default)
2
3
1
JBAT1: CMOS Setup (12)
If the board refuses to boot due to inappropriate CMOS settings here is how
to proceed to clear (reset) the CMOS to its default values.
Connector type: 2.00mm pitch x3 pin header
Pin
Mode
-2
Keep CMOS (Default)
2
3
1
2-3
Clear CMOS
2
3
1
You may need to clear the CMOS if your system cannot boot up because
you forgot your password, the CPU clock setup is incorrect, or the CMOS
settings need to be reset to default values after the system BIOS has been
updated.
Refer to the following solutions to reset your CMOS setting:
Solution A:
. Power off the system and disconnect the power cable.
2. Place a shunt to short pin 1 and pin 2 of JBAT1 for five seconds.
3. Place the shunt back to pin 2 and pin 3 of JBAT.
4. Power on the system.
Solution B:
If the CPU Clock setup is incorrect, you may not be able to boot up. In this
case, follow these instructions:
. Turn the system off, then on again. The CPU will automatically boot up
using standard parameters.
2. As the system boots, enter BIOS and set up the CPU clock.
Note:
If you are unable to enter BIOS setup, turn the system on and off a few
times.
Содержание 3308200
