Light duty Electric workbench, 2 x legs
Lay out all components and hardware to ensure that you have all the components
an
d
hardware liste
d
on the parts page.
Fully separate the Crossbar Ends (P3). You will find the Crossbar Center Rails (PS) inside.
1$
f
Prop up the assemblies from Step 1,
T
x
4
;:s:::::,
M6*10
Machine Screws(P21)
�'
1
tf
2
•
th,o,gh the holes of each Cros,ba, E•d(P3)
0
·
\
going into the Leg(Pl} an
d
tighten the
.
- - -
' -
screws.
i
,
Attach the Side Brackets(P4) to the
•
Leg/Crossbar End assembly with two M6*10
Machine Screws(P21}.
Repeat this step with the other assemblies.
Sli
d
e the two Crossbar Center Rails(PS) into the two
Crossbar Ends (P3).
Then to connect Leg(Pl and P2) an
d
Control Box(PS) with
Motor Cord(P8).
Please connect the wire of the Switch(P7) to the
Control Box(P&).
Please plug the Power Cord(P9) into the Control
Box(P&).
Attach the Short Rungs(Pl2) to the Leg with
four M6*10 Furniture Screws(P25).
Then attach the Long Rung(P13) to the Short
Rungs(P12) with four M6*16 Machine Screws(P21)
and four Butterfly Nut M6(P26).
Attach a Foot(PlO) with four M6*16 Machine Screws(P22)
into each leg(Pl and P2) and tighten screws.
Connect four Adjusting Nut(Pll) together with each
Foot(PlO}.
Place the table un
d
er the accessories an
d
place it in
correct position.
Please make sure the position of the desk and
tabletop are suitable for each other.
Please attach the tabletop with the
d
esk frame
with six(6) M5"16 Wood Screws(P23) and
tighten the screws.
Please insert eight M6*10 Machine Screws (P21}
through the holes in each Crossbar Ends(P3} going
into the Center Rails(PS) an
d
tighten the screws.
Please attach the Control Box(P&) un
d
er the
tabletop with two M5*16 Wood Screws(P23}.
Please also attach the 5witch(P7) un
d
er the
tabletop with two M4*16 Wood Screws(P24).
Turn the assemble
d d
esk right-si
d
e-up.
It' s
d
one.
Plug the Power Cor
d
(P9) into a 110V-240Voutlet.
A
Make sure no obstacles are in the
d
esk's path.
Make sure the
d
esktop is not touching any walls.
Make sure all cords are appropriate length to
Important You musti�i�Wii
d
ag�iii6rt2i�t
height.
Reset Proce
d
ure: Press an
d
hol
d
the DOWN button on the Switch {P7) until the
d
esk reaches its lowest height.
Release the DOWN button. Press an
d
hol
d
the DOWN button again until the LED
d
isplay reads "RST" or
about 10 secon
d
s on non-LED han
d
set mo
d
els. Release the DOWN button. Press an
d
hold the DOWN button
again until the
d
esk lowers a little bit more, slightly rises and stops. Release the DOWN button. Your desk is
now rea
d
y to use.
To program up to four presets (on some mo
d
els): Use the up/
d
own buttons to fin
d
a
d
esired height, then
press "M" ( ·s· on some mo
d
els) followe
d
by a number 1--4.
Caution: Once a preset button is pushed, the
d
esk will move to the programme
d
height(see caution box above).
Troubleshooting
If your
d
esk is not functioning properly it may nee
d
to be reset. Unplug the power cor
d
for 20 secon
d
s.
Plug the power cor
d
back in an
d
follow the RESET proce
d
ure outline
d
in Step 11.
If your
d
esk has a han
d
set with an LED rea
d
out and it
d
isplays "RST" (reset), perform the reset
proce
d
ure outline
d
in Step 11.
If the LED rea
d
out
d
isplays an error message ( "Erl· - "Er13" l confirm that all wire
d
connections are
secure(legs to cables, cables to control box). Then perform the reset proce
d
ure outline
d
in Step 11.
If the error message persists after the reset proce
d
ure, contact your seller.
If the height between the legs excee
d
s 1.5 inches, stop the reset proce
d
ure&contact your seller.
If the han
d
set
d
isplays "HOT" , let the base cool
d
own for 20 minutes.
Assembly Instructions
Содержание 493778GY
Страница 3: ......
