background image

1

The SST 09 ARF is distributed exclusively by Global Hobby Distributors   18480 Bandilier Circle  Fountain Valley, CA  92728

I N S T R U C T I O N S   F O R   F I N A L   A S S E M B L Y

All contents copyright © 2000, Global Hobby Distributors  Version V1.2  6/00

The Global SST 09 ARF is in no way a primary trainer.  If you have not flown an R/C airplane before, please
return this kit to the place of purchase before going any further.  The SST 09 is designed for those pilots who are
already skilled at flying a basic trainer or sport airplane.  Even though the SST 09 is small, it can be a very high
performance aircraft, depending upon which engine and radio accessories you use.  These options are discussed
in further detail to help you make the right choice for your desired style of flying.

To make your modeling experience totally enjoyable, we recommend that you get experienced, knowledgable
help with assembly and during your first flights.  Your local hobby shop has information about flying clubs in
your area whose membership includes qualified instructors.  We also recommend that you contact the AMA at
the address below.  They will be able to help you locate a flying field in your area also.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN.  47302-9252

(800) 435-9262

www.modelaircraft.org

Electric Conversion Instructions Included

in This Manual - See Page 26 for Details!

Содержание Global SST 09 ARF

































Отзывы: