Global Fire Equipment CHAMELEON GEKKO страница 27 Скачать руководство пользователя

Страница: 27 / 29

Global Fire Equipment //

globalfire.pt

ma_chmcomm_01_010001_en_191121

Upload a configuration without broadcast

Panel 1

, due to USB Chameleon Connector Config Update, changed the local configuration and the configuration was not

broadcasted to other system panels. All panels will trigger “Panel Configuration Mismatch” on Panel 1. Panel 1 will trigger

the fault mentioning all other panels on the queue.

After an USB Config Update the menu

8-5-4 Broadcast Configuration

should be executed in order to copy same

configuration to all network panels.

The following errors should be mentioned on the panels:

Panel 1

Panel 2

Panel 3

PANEL 02

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0002

PANEL 01

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0001

PANEL 01

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0001

PANEL 03

PANEL CONFIGURATION MISMATCH

TOTAL NUMBER OF FAULTS 0002

Содержание CHAMELEON GEKKO






























Результаты поиска

Содержание CHAMELEON GEKKO

Отзывы:

Похожие инструкции для CHAMELEON GEKKO

Бренды по названию

Популярные бренды

Global Fire Equipment CHAMELEON GEKKO, Инструкция по установке и наладке

Результаты поиска

Содержание CHAMELEON GEKKO

Отзывы:

Похожие инструкции для CHAMELEON GEKKO

Бренды по названию

Популярные бренды