GLI PROTECT-A-POOL Скачать руководство пользователя страница 3

STEP 2-A

Install mounting bracket to each upright (DIA-
GRAM 2-A). When installing your fence, it is 
important that there is no more than a 4" gap
between the pool’s top rail and the bottom rail of
fence. To determine location of mounting bracket,
simply line up bracket with a fence post attached
(slide fence post onto mounting bracket, but do
not permanently attach fence post to mounting
bracket as it will need to be removed), and meas-
ure gap between top rail of pool and bottom rail
hole in the post. Anywhere between 0 and 4" gap
is acceptable. Once location is determined, remove
post and attach mounting bracket to upright using
two #12 x 1” self-tapping screws.

Once installed, measure exact distance from the
bottom of the top rail to the mounting bracket. Use
that same measurement to determine location of
remaining mounting brackets. It is important to
take an accurate measurement as the levelness of
the fence is determined by the location of the
mounting bracket.

DIAGRAM 2-A

STEP 2-B
INSTALLATION OF “ARTIFICIAL
UPRIGHT” TO INSTALL FENCE UP TO
A-FRAME LADDER OR DECK:

Requires one 4 x 4 wooden post and one 2"
sheet-metal screw. Position ladder next to a
pool upright so it can hold the fence on one
side. Determine location for the "Artificial
Upright" and dig a hole approximately 6"
into the ground.
Measure from the bottom of hole to top of
pool and cut the 4 x 4 post to fit the span.
Place the 4 x 4 post into the ground so it fits
snug to the pool wall. Attach the 4 x 4 to the
pool structure by using one 2" sheet metal
screw. Screw down through the top rail into
the 4 x 4 wooden post. Fill in around the
hole with remaining dirt. Continue by
mounting support brackets to wooden
post using instructions (2-A).

NOTE

Be sure the pool entrance has a self-closing and self-latching gate.

DIAGRAM 2-B

Содержание PROTECT-A-POOL








Отзывы: