gledhill BOILERMATE OV PP Скачать руководство пользователя страница 3

Страница: 3 / 52

Page 3

DESIGN

INTRODUCTION

Any water distribution system/installation must comply with the relevant

recommendations of the current version of the Regulations and British Standards

listed below:-

Gas Safety (Installation and use) Regulations 1998

Building Regulations

Water Supply (Water Fittings) Regulations 1999

Manual Handling Operations Regulations

British Standards

BS EN 806:1-5: BS EN 8558:2011

Requirements for Electrical Installations BS7671:2008 and A2:2013 18th Edition

Most new building work will require the relevant building control body to be notified

prior to the building work commencing. This will not be required if the work is carried

out under a self certification scheme or if the work is not notifiable. Full details of the

self certification schemes and work that is not notifiable can be obtained from page

9 of Approved Document G, available from www.planningportal.gov.uk.

A suitably competent trades person must install the BoilerMate and carry out any

subsequent maintenance/repairs. The manufacturer’s notes must not be taken as

overriding statutory obligations.

The Domestic Building Services Compliance Guide 2013 defines, one of the fixed

building services, as any part of or controls associated with fixed systems for domestic

hot water. All fixed building services, including theircontrols, should be commissioned

by testing and adjustment to ensure that they use no more fuel and power than is

reasonable in the circumstances. Where commissioning is required, if it is completed

by a person registered with a competent person scheme, the commissioning notice

will be supplied by that person, otherwise the person carrying out the work must notify

the relevant building control body, that commissioning has taken place in accordance

with the Domestic Heating Compliance Guide.The building control body will then be

able to issue a completion certificate. This applies to England, for other jurisdictions in

the UK, it may be necessary to consult their own building regulations and guidance.

The BoilerMate is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience or knowledge, unless

they have been given supervision or instruction concerning use of the appliance by

a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The information in this manual is provided to assist generally in the selection of

equipment. The responsibility for the selection and specification of the equipment

must however remain that of the customer and any Designers or Consultants

concerned with the design and installation.

Please Note:

We do not therefore accept any responsibility for matters of design,

selection or specification or for the effectiveness of an installation containing one of

our products unless we have been specifically requested to do so.

All goods are sold subject to our Conditions of Sale, which are set out at the rear of

this manual.

In the interest of continuously improving the BoilerMate range, Gledhill Building

Products Ltd reserve the right to modify the product without notice, and in these

circumstances this document, which is accurate at the time of printing, should be

disregarded. It will however be updated as soon as possible after the change has

occurred.

The Environment

This product has been manufactured using

many recyclable materials, including the

approved HCFC/CFC free polyurethane foam

insulation. At the end of its useful life, it

should be disposed of at a Local Authority

Recycling Centre, to maximise the products full

environmental benefits.

Содержание BOILERMATE OV PP





















































Результаты поиска

Содержание BOILERMATE OV PP

Отзывы:

Похожие инструкции для BOILERMATE OV PP

Бренды по названию

Популярные бренды

gledhill BOILERMATE OV PP, Инструкция по эксплуатации

Результаты поиска

Содержание BOILERMATE OV PP

Отзывы:

Похожие инструкции для BOILERMATE OV PP

Бренды по названию

Популярные бренды