gledhill BOILERMATE OV PP Скачать руководство пользователя страница 12

Страница: 12 / 52

Page 12

Preparation / Placing The Appliance in Position

The appliance should be handled carefully to avoid damage and the recommended

method is shown above.

Note

: Although the above guidance is provided any manual handling/lifting

operations will need to comply with the requirements of the Manual Handling

Operations Regulations issued by the H.S.E.

The appliance can be moved using a sack truck on the rear face although care should

be taken and the route should be even.

In apartment buildings containing a number of storeys we would recommend that

the appliances are moved vertically in a mechanical lift.

If it is proposed to use a crane expert advice should be obtained regarding the need

for slings, lifting beams etc.

Before installation the site requirements should be checked and confirmed as

acceptable.

Manual Handling Of The Appliance

Manual handling means any transporting or supporting of a load (including lifting,

putting down, pushing, pulling, carrying or moving) by hand or bodily force.

Scope

This assessment will cover the largest unit within each product range.

For specific weights and dimensions please refer to technical data section.

Main Hazards

Vision may not be clear due to the size of the products.

Adopting an incorrect method of lifting may cause injury, attempting to lift these

products will require help from others. (Team lifts)

Manual Lifting Procedure

The lift, key factors in safe lifting are:

Balance

Position of back

Positioning of the arms and body

The hold

Taking the lead for team lifts

Balance -

Since balance depends essentially upon the position of the feet, they

should be apart about hip breadth with one foot advanced giving full balance

sideways and forward without tension. In taking up this position, lifting is done

by bending at the knees instead of the hips and the muscles that are brought

into use are those of the thigh and not the back.

Position of back

- Straight - not necessary vertical. The spine must be kept

rigid, this coupled with a bent knee position, allows the centre line of gravity of

the body to be over the weight so reducing strain.

Positioning of arms and body

- The further arms are away from the side, the

greater the strain on the shoulders, chest and back. Keep elbows close to the

body arms should be straight.

The hold

- Before lifting ensure you have

a good hold.

Taking the lead for team lifts

- As more

than one person is required for these

products ensure that one person is taking

the lead.

This may be you

so ensure that

each person that is helping is made aware

of the weight and of the items listed within

this assessment. Make sure you and any

others helping know the route you intend

to take that it is clear of any obstructions.

Never jerk the load as this will add a little

extra force and can cause severe strain

to the arms, back and shoulders. If there

are steps involved decide on where you

will stop and take a rest period. Move

smoothly and in unison taking care to

look and listen to others helping with the

lift. Where possible use a sack truck to

move the product over long flat distances,

only lift the products when necessary. If in

doubt stop and get more help.

Individual Capability

Individual capability plays an important part

in handling these products. Persons above

average build and strength will find it easier

and should be in good health. Persons below

average build and strength may require more

rest periods during the handling process.

Pregnant women should not carry out this

operation.

Persons who are not in good health should

seek medical advice prior to commencing any

lifting or manual handling operation.

Residual Risk

Following the guidelines given above will

reduce any risk to injury.

All persons carrying out this operation must

be fully trained and copies of the specific risk

assessment made available for inspection and

use in their training process.

Further guidance on Manual Handling can be

obtained from the Health and Safety Executive.

Manual Handling Operations Regulations 1992

(amended by Health and Safety (Miscellaneous

Amendments) Regulations 2002.

TRANSPORT

LIFTING AND HANDLING

Содержание BOILERMATE OV PP





















































Результаты поиска

Содержание BOILERMATE OV PP

Отзывы:

Похожие инструкции для BOILERMATE OV PP

Бренды по названию

Популярные бренды

gledhill BOILERMATE OV PP, Инструкция по эксплуатации

Результаты поиска

Содержание BOILERMATE OV PP

Отзывы:

Похожие инструкции для BOILERMATE OV PP

Бренды по названию

Популярные бренды