background image

Sliding touch fail

 

The  speed  of  sliding  touch  is 

too fast

 

Slow down the speed of sliding touch 

Malfunction code “E1”

 

Current leakage

 

Contact the service centre for repair

 

Malfunction code “E2”

 

Water  Flow  switch  is  open  or 

short circuit

 

Contact the service centre for repair

 

Malfunction code “E3”

 

The  temp.  sensor  of  outlet  is 

short circuit or open circuit

 

Malfunction code “E4”

 

The  temperature  of  outlet 

water  is  higher  than  60 

degrees

 

Check the cause of so high temperture

If the solution instruction we provided can not solve the  problems, please contac

professional maintenance man.   

Other key notices: 

 

The water heater

 

must be earthed.

 

The earth wire and zero line shall be strictly isolated.

 

When abnormal occurrence happens, make sure power dump immediately and contact maintenance man

soon as possible. It is dangerous to fix it by yourself. 

 

DO NOT

 

turn on the power switch when water in the tank is frosted. 

 

DO NOT

 

use plump cement on connecting. If necessary, use only thread or seal-tape.

 

Shut off the power immediately if there is a large amount water flowing out from the water heater.

 

Have a service life of any product, please use the period stipulated by the state scrapped, due either 

scrapped or abandoned half-way updating, should be sent to the local waste collection stations.

 

 

as 

12

 

Содержание GL5















Отзывы: