IMPORTANT:
Determine if your Tub/Shower
Stall Enclosure ledge is Level and
the Wall are plumb.
• 3/8” max. OOS (Out Of Square)
for the Door Side;
• 5/8”max. OOS (Out Of Square)
for the Panel Side;
• 3/8” max. OOS (Out Of Square)
on the Bottom (Base)
of the enclosure;
If your unit is Out-Of-Square or
Plumb greater than above STOP!
and call Customer Service.
The Phone number is
1-888-683-1362
.
2 3/4” MINIMUM CURB WIDTH
REQUIRED
When ordering replacement parts,please specify the Model Number, Item Number & Part Description.
Save these Installation Instructions For Future Reference.
Write your Dealer information down on Notes Section in the back of this guide. Ask your Dealer for JOB LOG NUMBER
(Lxxxxxx-xxx) Referencing to your shower enclosure.
ITEM NO. DESCRIPTION QTY.
1 Vertical Wall Jamb ....................1
2 Fixed Glass Panel ....................1
3. Glass Door................................1
4. Door Handle Assembly .............1
6. Bottom “U” Channel..................1
7. Clear Setting Blocks .................3
8. Center Guide Assembly............1
9. Horizontal Rail .........................1
(with Panel Screw Assembly
....
10. Horizontal Rail Mounting
Wall Brackets ..........................2
11. Plastic Guide Insert ..................1
12. Door Stop/Bumper....................2
13. Roller Assembly........................2
14. Panel Screw Assembly .............2
(with Header
............................
15. Anti-Lift Standoff Assembly.......2
16. Clear “Bubble” Vinyl Bumper ....1
17. End Cap .................................1
18. Curb Dam .................................1
19. Clear “H” Vinyl .........................1
20. Plastic Wall Anchors.................12
21.Pan Head Screws, #8 x 1 1/4” ..7
22. Flat Head Screws, #8 x 1 1/4”..5
23. Hex Key Set (4)........................1
24. Splash Guard ...........................1
Parts Description
2
CAUTION:
Risk of injury or product damage. Do not attempt to cut tempered glass.
IMPORTANT!
Children should be supervised at all times while in Tub/Shower Enclosure.
IMPORTANT!
Never use Door Handle or Towel Bar to support yourself. This is for towels or wash cloths only.
PLEASE STOP THE INSTALLATION AND CONFIRM WITH FACTORY IF THE ACTUAL NUMBER OR TYPE OF PARTS IS DIFFERENT
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
:
Glasscrafters recommends the installation
be performed by a trained installer.
• Read the manual and become familiar
with the steps involved in installation.
• This product requires Two persons for
safe installation.
• Always wear safety glasses during this in-
stallation.
• The proper dimensions for this
installation were submitted at the time of
order. The Glass Panel and Door may
overlap to accommodate minor smaller
opening. One end of the Horizontal Rail
many be cut with a hacksaw for stainless
steel, but it must fit completely in the
Horizontal Rail Mounting Brackets for a safe
installation.
• When installing any mechanical parts
through the pre-drilled holes in the glass
door and panel be sure to use the gaskets
and bushings supplied between any metal
element and the glass. Do no over-tighten
any fittings.
• The glass used in this enclosure is
Tempered Safety Glass and features a
Tempered Safety Glass logo. Do not install if
Tempered Safety Glass logo is missing.
Call Customer Service.
• Tempered Safety glass cannot be cut,
ground, polished or manipulated in any
way.
• If the installation is over ceramic tiles the
wall Jamb must lay flat on these tiles for the
entire height of the unit.
• Silicone Sealant is used to seal some parts
during installation and the inside of the
enclosure as shown in Detail #10. Do not
caulk from the outside of the enclosure.
Tools Required - For installation of Your Shower Enclosure
Safety glasses
Measuring tape
Pencil
Hacksaw or chop saw
(for stainless steel)
Miter Box or
Square
Level
Electric Drill/
Power Screwdriver
Center Punch
Rubber Mallet
Drill bit,
5/16” masonry
(for installation
on ceramic tiles
or marble)
#2 phillips
screwdriver
Caulking gun
Cutting Pliers
Suction Glass Lifters
(rated for more than 100 lbs)
WARNING: TO INSTALL ON CAST IRON, FIBERGLASS, ACRYLIC
OR RESIN TUB OR SHOWER BASE-
-
Check with the tub or shower base
manufacturer to determine the tooling required.
LOCTITE
243
BLUE
Loctite 243 Blue
Threadlocker
Medium strenght
