15
HOME MODE (HO):
Start
nighttime
temperature cutback
At the time of evening you wish temperature cutback to
start, press the button for more than five seconds.
h (hours) will flash three times in the display and then 7
will flash continuously. With the or key select the
number of hours you want the temperature cutback pe-
riod to last. When your selection is displayed, confirm
it by pressing the button briefly.
°C will flash three times and then 17 (°C) will flash
continuously. Using the or key, select the
temperature you wish for the cutback period. When
your selection is displayed, confirm it by pressing the
button briefly.
Lamp
➃
will now flash slowly to indicate that tempera-
ture cutback is active. The temperature is reduced for
the number of hours you have chosen, and this will be
repeated for the same period every night.
Start
daytime
temperature cutback
At the time you wish temperature cutback to start,
press for more than five seconds.
h (hours) will flash three times and then 5 will flash
continuously. Using the or key, select the number
of hours you want the temperature cutback period to
last. When your selection is displayed, confirm it by
pressing the button briefly.
d will flash three times and then a random number. Us-
ing the or key, enter the correct day of the week
(Monday = 1, etc.). Confirm by pressing the button
briefly.
°C will flash three times and then 17 (°C) will flash
continuously. With the or key select your
preferred cutback temperature. Confirm by pressing
button briefly.
Lamp
➀
will now flash slowly to indicate that daytime
temperature cutback is active. The temperature is
reduced to your selected setting for the number of hours
you have chosen. This will be repeated for the same
period every weekday, leaving Saturday and Sunday
unaffected.
Calibration
(to make sure that the displayed temperature corresponds with the correct room temperature)
Should the actual room temperature and the thermostat’s displayed setting not correspond, the thermostat may be
calibrated.
NB! Correct calibration depends on room temperature being regulated by the heater’s thermostat alone. This is
shown by the red lamp lighting and dimming at regular intervals. If necessary, adjust the thermostat up or down to
make the heater start working.
Now allow the heater to work at the same temperature setting, preferably for at least 24 hours, keeping doors and
windows closed in the room. This ensures that the heater’s thermostat alone is regulating the temperature of the
room.
Holding down on , press once on the key briefly. Release .
°C will flash three times and the setpoint temperature is displayed. Press the or key until the display shows the
same as the actual measured room temperature. Save by pressing the button briefly.
The heater will now display the setpoint temperature again, and after a while this will correspond with the actual
room temperature. It may be necessary to repeat the calibration procedure to attain full correlation between desired
and actual room temperature.
OFFICE MODE (OF):
To enter office mode hold down and press for
more than five seconds until OF flashes and 20 (°C) is
displayed.
Starting the temperature cutback function
Three hours before you usually leave the office press
and hold down the button for five seconds (e.g. at
14:00 – 2 PM).
h (hours) will flash three times in the display, then 12
will flash. Select the number of hours you want tem-
perature cutback to last by pressing the or key.
Confirm by pressing briefly. (NB! Cutback will start
after three hours.)
d (day) will flash three times, then a random number
will be displayed. Enter the correct day using the
or key (Monday = 1, etc.). Confirm by pressing
briefly.
cL (time of day) will flash three times, and 16 is dis-
played. Use the or key to enter the closest whole
hour of the day. Confirm by pressing briefly.
°C will flash three times and then 16 is displayed. With
the or key, select your preferred cutback tempera-
ture. Confirm by pressing the button briefly.
Comfort temperature will continue for three hours
before the cutback period starts automatically.
(E.g. Pressing at 14:00 – 2 PM – will make tempera-
ture cutback start at 17:00 – 5 PM and the lamp will flash
slowly. During the three hours before cutback start the
lamp is lit steadily.)
Working overtime
When working overtime the cutback function may be
overridden. Press for more than five seconds. The set
comfort temperature will be displayed. Lamp
➀
will
light steadily while the lamp
➃
continues to flash. This
temporary period of comfort temperature will last for
five hours.
GB/AU/NZ
