manualshive.com logo in svg

Gis GP 1000, Инструкция по эксплуатации

Поделиться
Скачать
Gis GP 1000 Скачать руководство пользователя страница 12

12

Swiss Lifting Solutions

2.2.1  Electrical connections

Electrical installations may only be performed by authorised specialists.

The mains connection cable, the mains connection fuse and the main switch for connecting the electric chain hoist to the mains power 

supply must be provided by the customer. A 4-wire cable with a PE protective conductor is needed as a supply line for three-phase  

versions. A 3-wire cable with a protective conductor is adequate for single-phase version. The length and cross-section must be  

appropriate for the power consumption of the electric chain hoist.

2.2 Connections

The safety directions for handling with loads should be followed (see chapter 0.3) when transporting and assembling the electric chain 

hoist. Electric chain hoists must be assembled by qualified staff, always bearing in mind the accident prevention directions in chapter 0.2. 

Before assembly, the electric chain hoist must be stored in an closed room or covered area. Should the electric chain hoist be destined for 

operation outdoors, then it is recommended that a protective cover is erected to shield it from the effects of the weather.

Wherever possible, the electric chain hoist should be transported in its original packaging. The goods delivered should be checked for 

completeness and the packaging disposed in an environmentally sound manner. It is recommended that the electric chain hoist is assem-

bled and connected on-site by qualified personnel.

2.1  Transport and assembly

Mechanical adjustments may only be performed by authorised specialists.

Operating staff must carefully read the instruction manual of the electric chain hoist before initial start-up and carry out all the 

checks. The device shall be put back into operation only after operational safety has been established. Unauthorised persons 

may not operate the device or carry out work with it.

The operator must create an inspection pass during the commissioning of the electric chain hoist. The inspection pass con-

tains all the technical data and the date of commissioning. It provides a record of all servicing and maintenance work.

2 Start-up

By pressing the emergency stop button, the power supply to the electric chain hoist is interrupted in all phases. The movement of the  

electric chain hoist is stopped immediately. To unlock the emergency stop button, it must be turned in the indicated direction.

After an emergency stop, the operator may only restart the electric chain hoist after a competent person is satisfied that the 

cause which led to the emergency stop has been eliminated and that there is no longer any danger from further operation of 

the system.

1.3  Emergency stop

 

 

 

 

 

Содержание GP 1000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды