Gis GP 1000, Инструкция по эксплуатации

Страница: 10 / 28

10 90
100
80
50 50
100
33
16.7 50
100
0 ~
40
16.716.7
70
10 40 50
100
0 ~
40
10 Swiss Lifting Solutions
Example 1: Calculate permissible operating time of the electric chain hoist
An electric chain hoist of the classification A4 is to be used for medium stress load tasks throughout its whole calculated service life.
This corresponds to the type of load "Q4 heavy" (see table 1-1). Corresponding to the values in table 1-2, the electric chain hoist should
not be used for more than 60 cycles per day.
Example 2: Calculate the permissible type of load
An electric chain hoist of the classification A5 is to be used for approximately 400 cycles per working day, throughout its whole service life.
Thus, the electric chain hoist must be operated in accordance with the characteristics of the type of load 'Q2 light' (see table 1-1).
Ascertaining the correct type of application for an electric chain hoist:
Either the number of cycles or expected type of load can be used as a basis for ascertaining the correct type of application for the electric
chain hoist.
Before initial start-up of the electric chain hoist, it is necessary to ascertain which of the load types in table 1-1 applies to the
operation of the electric chain hoist. Assignment to a load type or a load spectrum (Q) applies for the whole service life of the
equipment and may not be altered for operational safety reasons.
Classification according to
DIN EN 14492-2 (ISO 4301-1)
A3 (M3) A4 (M4) A5 (M5) A6 (M6) A7 (M7)
Load spectrum
Number of cycles per working day
(hoisting classes Dh2 - Dh5, lifting speed 8 m/min)
Q2 - light Q < 0.50 120 240 480 960 1 920
Q3 - medium 0.50 < Q < 0.63 60 120 240 480 960
Q4 - heavy 0.63 < Q < 0.80 30 60 120 240 480
Q5 - very heavy 0.80 < Q < 1.00 15 30 60 120 240
Table 1-2 Operating conditions
Q = Load spectrum (type of load)
Load type Q2
light
Q < 0.50
Q = 0.50
Load type Q3
medium
0.50 < Q < 0.63
Q = 0.63
Load type Q4
heavy
0.63 < Q < 0.80
Q = 0.80
Load type Q5
very heavy
0.80 < Q < 1.00
Q = 1.00
%
o
f l
ift
in
g c
apa
cit
y
%
o
f l
ift
in
g c
apa
cit
y
%
o
f l
ift
in
g c
apa
cit
y
%
o
f l
ift
in
g c
apa
cit
y
% of operating time % of operating time % of operating time % of operating time
Full load only by way
of an exception,
however predominantly
low loads
Often fully loaded,
however continuously
lightly loaded
Frequently fully loaded
continuous average
loading
Regularly fully loaded
Table 1-1 Load spectrums
The manufacturer will only guarantee the safety and lasting operation of the electric chain hoist when used for applications in accordance
with valid standard values that fall within its classification.
Before the initial start-up, the user must estimate according to the parameters in table 1-1, which of the four types of load is applicable to
the use of the electric chain hoist during its whole life cycle. The table 1-2 shows standard values for the operating conditions of the
classifications depending on the type of load and number of cycles.
The travel trolley must have at least the same lifting capacity as the electric chain hoist.
The classification of the electric chain hoist can be found on the data plate.