background image

Current dimming value

The load can be dimmed using the slider or a
brightness value entry.

Load state

The load can be switched on or off.

Restraint

Display of forced position status.

Switching cycle counter

Display of the switching cycles with the factor
10, e.g. the value 5 x 10 is displayed for 50
switching cycles.

Total operating hours

Display of the operating hours since the start
of operation.

Operating hours

Display of the operating hours since the last
restart in the Settings window. 

6.3 Troubleshooting

Lamps switch to minimum brightness. No dimming is possible.

Cause 1: 1-10 V interface is connected in reverse polarity.

Connect the control cables with the correct polarity.

Cause 2: 1-10 V control cables have short-circuited.

Eliminate short-circuit.

Lamps switch to maximum brightness. No dimming is possible.

Cause: 1-10 V control cables are interrupted or not connected.

Connect the control cables correctly.

6.4 Accessories

Installation adapter Mini housing

Order No. 5429 00

DRA server

Order No. 5301 00

6.5 Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your
responsible salesperson (specialist trade/installation company/electrical specialist trade). They
will forward the devices to the Gira Service Center. 

Gira
Giersiepen GmbH & Co. KG

Elektro-Installations-
Systeme

Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald

Postfach 12 20
42461 Radevormwald

Deutschland

Tel +49(0)21 95 - 602-0
Fax +49(0)21 95 - 602-191

www.gira.de
[email protected]

32581002

10499448

13.03.2014

11/11

eNet

Radio control unit 1-10V, 1-gang Mini

Содержание eNet












Отзывы: