13
Before cleaning the microscope, unplug it from power supply!
Never clean the optical surfaces with paper tissues and cloths!
Do not use pure alcohol to clean optical components!
Do not dismantle and never clean the internal surfaces of the microscope optical
components!
Remove the oil from the 100X lens after each employment!
16
17
preservation of the objective lens and eyepieces, it is advisable to use dehumidification agents.
- In case you need to move the microscope, hold it by the holder column. Do not seize it by the
eyepiece or objective lenses.
The microscope metallic parts can be cleaned with a slightly wet cloth.
The optical components (objective lenses, eyepieces, condenser) must be daily cleaned as follows:
blow away the dust by means of a little pump or compressed air bomb. Alternatively it is possible to
remove the dust with a clean brush with non-abrasive bristles.
To thoroughly clean the optical components (objective lenses, eyepieces, condenser) and to remove
the oil from the 100X objective, make use of a wad of cotton-wool soaked with a alcohol/ether solution
or diethyl benzene.
REPLACING THE LAMP
1. Switch off the microscope and
disconnect the power cable.
2. Remove the eyepieces and put them
back in the box.
3. Tilt the microscope, remove the
screw of the door in the front part of
the base of the microscope and open
to reach the lamp
.
3. Remove the old lamp
4. Put in the new lamp and make sure
it is positioned correctly.
5. Clean the new lamp with alcohol.
6. Close the door and fix it with a
screw.
7. Connect the power cable, switch on
the microscope, position the lenses,
adjust the height of the condenser and
make sure light reaches the field of
focus.
REPLACING THE FUSES
1. Remove the screws under the five feet of the base of the microscope and remove the base from the
column making sure not to tear the earth wire which connects the two parts.
2. Verify which of the two fuses
on the base is burned and remove it. Replace it with a new one.
3. Reposition the base and put the five screws back on.
Specifications of fuse: 250 mA - 250 V
Содержание 31001
