Pound Weight Sets
Model
Total Mass
Total Load at 10:1
Beam Ratio¹
Included Weight Sets
0.852lb (1/8tsf)
1.704lb (1/4tsf)
3.409lb (1/2tsf)
6.818lb (1tsf)
13.635lb (2tsf)
27.270lb (4tsf)
HMA-727
HMA-732
HMA-729
54.5lb
109.1lb
218.2lb
545lbf (8tsf)
1,091lbf (16tsf)
2,182lbf (32tsf)
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
3
7
¹tsf values indicate force applied to a 2.50in diameter specimen using a 10:1 beam ratio.
Kilogram Weight Sets
Model
Total Mass
Total Load at 10:1
Beam Ratio
Included Weight Sets
1kg
4kg
8kg
HMA-730
HMA-725
HMA-731
32kg
64kg
88kg
320kg
640kg
880kg
4
4
4
3
5
5
2
5
8
Description
Consolidometer
Calibration
Disc
50mm (1.969in) Fixed Ring Consolidometer
2in (50.8mm) Fixed Ring Consolidometer
60mm (2.36in) Fixed Ring Consolidometer
2.42in (61.5mm) Fixed Ring Consolidometer
2.5in (63.5mm) Fixed Ring Consolidometer
70mm (2.756in) Fixed Ring Consolidometer
75mm (2.95in) Fixed Ring Consolidometer
3in (76.2mm) Fixed Ring Consolidometer
HMA-83A
HMA-83B
HMA-83C
HMA-83D
HMA-83E
HMA-83F
HMA-83G
HMA-83H
HMA-88A
HMA-88B
HMA-88C
HMA-88D
HMA-88E
HMA-88F
HMA-88G
HMA-88H
50mm (1.97in) Floating Ring Consolidometer
2in (50.8mm) Floating Ring Consolidometer
2.42in (61.47mm) Floating Ring Consolidometer
2.5in (63.5mm) Floating Ring Consolidometer
70mm (2.76in) Floating Ring Consolidometer
HMA-84A
HMA-84B
HMA-84D
HMA-84E
HMA-84F
HMA-88A
HMA-88B
HMA-88D
HMA-88E
HMA-88F
OPTIONAL ACCESSORIES
(Purchased Separately)
• HMA-89 Consolidation Load Frame Stand
• Calibration Discs (refer to Consolidometer chart above)
• HMA-608 Consolidation Data Acquisition Software
UNPACKING & SETUP
1. Inspect the HM-353 for damage, remove it from the pallet.
2. Ensure the following items are included:
• Adjustable counterbalance weight with threaded rod and
nuts (x2)
• Dial Indicator support rod
• Dial Indicator adjusting bracket
• Weight hanger with connecting pin
• Load-holding screw with adjusting knob
• Anchor bolts (x2), nuts (x4) and washers (x4)
3. Unpack the required accessories (ordered separately):
• Weight Set(s)
• Consolidometer(s)
• Dial Indicator or LVDT and Digital Readout Box
4. Fasten the Load Frame to a sturdy table using the included
3/8” diameter by 5” long Anchor Mounting Bolts, making sure
there is enough clearance for the load-holding screw and the
weight hanger.
4a. Fasten the Load Frame to the Load Frame Stand. The stand
includes a front and back leg with four ¾”-16 x 1” Hex Head
Bolts, and four Hex Nuts.
Remove the two screws on the back underside of the load
frame base. Attach the back leg to this area using the longer
screws that were included with the stand.
Bolt the font leg into the base using the two of the included
bolts and two hex head bolts.
OPERATING INSTRUCTIONS
1. Read all safety and operating instructions before operating
the unit.
2. Consult ASTM D2435, ASTM D4546 or AASHTO T 216 for spe-
cific instructions on the testing procedures.
3. Fasten the weight hanger to the unit and adjust using the
connecting pin.
4. Secure the Dial Indicator support rod toward the back of the
base, fasten the Dial Indicator holder to the rod and then
connect the Dial Indicator or LVDT to the holder.
5. Insert the counterbalance weight with threaded rod approxi-
mately 1” and tighten the jam nut.
6. Balance the lever with the top loading arm by adjusting the
counterweight and tighten the nut.
7. Set the Consolidometer (with sample) on the platform and
turn the adjusting screw until contact is made with the load
pad in the Consolidometer.
8. Adjust the Dial Indicator or LVDT to the desired setting.
