A-2: Installation in Intel RST Premium With Intel Optane System Acceleration mode
If the SATA controller has been configured in
Intel RST Premium With Intel Optane System Acceleration
mode, please follow the steps below:
1. After system restarts, go to the BIOS Setup, make sure
CSM Support
under the
Boot
menu is disabled.
2. Go to
Settings\IO Ports\SATA And RST Configuration
and make sure
USE RST Legacy OROM
is disabled
and
RST Control PCIe Storage Devices
is set to
Manual
. If you want to enable the Optane
™
memory installed
in the M2A_SB connector, set
PCIe Storage Device On Port 9
to
RST Controlled
; to enable the Optane
™
memory installed in the M2M_SB connector, set
PCIe Storage Device On Port 17
to
RST Controlled
.
3. Enter the operating system, launch the
Intel
®
Rapid Storage Technology
utility from the Start menu, and
then enable Intel
®
Optane
™
Memory on the
Intel
®
Optane
™
Memory
screen.
4. If you install more than one Optane
™
memory, please select which one you are going to use. Then select
which drive to be accelerated. Click Yes to continue. Follow the on-screen instructions to proceed. When
completed, restart the system.
5. Launch the
Intel
®
Rapid Storage Technology
utility from the Start menu and make sure the Intel
®
Optane
™
Memory has been enabled. If you want to accelerate the system drive, you can select specific folders, files,
or applications to accelerate using the
Intel
®
Optane
™
Memory Pinning
function. (The Optane
™
memory
used must have at least 32 GB capacity.)
•
An Optane
™
memory cannot be used to accelerate an M.2 PCIe SSD.
•
If more than one Optane
™
memory is installed, you can select only one of them to accelerate your
SATA-based boot drive. The other(s) can only be used as data drive(s).
•
Do not abruptly remove the Optane
™
memory. Doing so will cause the operating system to stop
functioning correctly.
•
If you want to change/remove the Optane
™
memory, you must disable it using the Intel
®
Rapid
Storage Technology or Intel(R) Optane
™
Memory application first.
•
After enabling the Optane
™
memory, the related BIOS settings will remain even after a BIOS update.
Installation Guidelines
A-1: Installation in AHCI mode
If the SATA controller has been configured in AHCI mode, please follow the steps below:
1. After entering the operating system, insert the motherboard driver disc into your optical drive. On the Xpress
Install screen, select
Intel(R) Optane(TM) Memory System Acceleration
(Note)
to install. Follow the on-screen
instructions to continue. The system will auto-restart.
2. After re-entering the operating system, follow the on-screen instructions to complete the settings, and then the
Intel
®
Optane
™
Memory
application will appear automatically. If you install more than one Optane
™
memory,
please select which one you are going to use. Then select which drive to be accelerated. Click
Enable
. All
data on the Optane
™
memory will be erased. Make sure you back up the data before continuing. Follow the
on-screen instructions to proceed. When completed, restart the system.
3. Launch the
Intel
®
Optane
™
Memory
application from the Start menu and make sure the Intel
®
Optane
™
Memory has been enabled. (The SATA controller mode is changed to
Intel RST Premium With Intel Optane
System Acceleration
from AHCI mode. DO NOT change your SATA controller mode back to AHCI. Doing
so will cause the Optane
™
memory unable to function properly.)
4.
If you want to accelerate the system drive, you can select specific folders, files, or applications to accelerate using
the
Intel
®
Optane
™
Memory Pinning
function. (The Optane
™
memory used must have at least 32 GB capacity.)
(Note) If the system already has Intel
®
Rapid Storage Technology utility installed, you have to remove it first
before installing the Intel(R) Optane(TM) Memory System Acceleration application.
- 46 -
Содержание Z490 GAMING X
Страница 51: ...51...