Please visit GIGABYTE's website for details on configuring a RAID array.
C-2. UEFI RAID Configuration
Steps:
1. In BIOS Setup, go to
Boot
and set
CSM Support
to
Disabled
. Save the changes and exit BIOS Setup.
2. After the system reboot, enter BIOS Setup again. Then enter the
Settings\IO Ports\Intel(R) Rapid Storage
Technology
sub-menu.
3. On the
Intel(R) Rapid Storage Technology
menu, press <Enter> on
Create RAID Volume
to enter the
Create RAID Volume
screen. Enter a volume name with 1~16 letters (letters cannot be special characters)
under the
Name
item and press <Enter>. Then, select a RAID level. RAID levels supported include RAID 0,
RAID 1, RAID 10, and RAID 5 (the selections available depend on the number of the hard drives being
installed). Next, use the down arrow key to move to
Select Disks
.
4. Under
Select Disks
item, select the hard drives to be included in the RAID array. Press the <Space> key
on the hard drives to be selected (selected hard drives are marked with "X"). Then set the stripe block size.
The stripe block size can be set from 4 KB to 128 KB. Once you have selected the stripe block size, set the
volume capacity.
5. After setting the capacity, move to
Create Volume
and press <Enter> to begin.
6. After completing, you'll be brought back to the
Intel(R) Rapid Storage Technology
screen. Under
RAID
Volumes
you can see the new RAID volume. To see more detailed information, press <Enter> on the volume
to check for information on RAID level, stripe block size, array name, and array capacity, etc.
C-3. Configuring Legacy RAID ROM
You’ll need a discrete graphics card to enter the legacy RAID ROM utility. Enter the Intel
®
legacy RAID BIOS
setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating
system for a non-RAID configuration.
Steps:
1. In BIOS Setup, go to
Boot
and set
CSM Support
to
Enabled
and
Storage Boot Option Control
to
Legacy
.
Next, go to
Settings\IO Ports\SATA And RST Configuration
and make sure
Use RST Legacy OROM
is
set to
Enabled
. Save the changes and exit BIOS Setup. After the POST memory test begins and before the
operating system boot begins, look for a message which says "Press <Ctrl-I> to enter Configuration Utility".
Press <Ctrl> + <I> to enter the RAID Configuration Utility.
2.
After you press <Ctrl> + <I>, the
MAIN MENU
screen will appear. If you want to create a RAID array, select
Create RAID Volume
in MAIN MENU and press <Enter>.
C-1. Using EZ RAID
GIGABYTE motherboards provide you with the EZ RAID feature, allowing you to quickly configure a RAID
array with simplified steps.
Steps:
1. After restarting the computer, enter the BIOS Setup and go to
Settings\EZ RAID
. Press <Enter> on the
EZ
RAID
item. Select the type of hard drives you use for RAID in the
Type
tab and then press <Enter>.
2. Go to the
Mode
tab to select a RAID level. RAID levels supported include RAID 0, RAID 1, RAID 10, and RAID 5
(the selections available depend on the number of the hard drives being installed). Then press <Enter> to
move to the
Create
tab. Click
Proceed
to begin.
3. After completing, you'll be brought back to the
Intel(R) Rapid Storage Technology
screen. Under
RAID
Volumes
you can see the new RAID volume. To see more detailed information, press <Enter> on the volume
to check for information on RAID level, stripe block size, array name, and array capacity, etc.
- 44 -
Содержание Z490 GAMING X
Страница 51: ...51...