Gigabyte R282-G30 Скачать руководство пользователя

Страница: 19 / 109

- 19 -

System Appearance

2-3 Front Panel LED and Buttons

1
3
5
7

2
4
6
8

No. Name

Color

Status

Description

Reset Button

Press this button to reset the system.

NMI button

Press this button for the server to generate a NMI to the
processor. If multiple-bit ECC errors occur, the server will
effectively be halted.

Power button
with LED

Green

Indicates the system is powered on.

Green

Blink

System is in ACPI S1 state (sleep mode).

N/A

Off

- System is not powered on or in ACPI S5 state (power
off)
- System is in ACPI S4 state (hibernate mode)

ID Button
with LED

Blue

Indicates the system identification is active.

N/A

Off

Indicates the system identification is disabled.

HDD Status
LED

Green

Indicates locating the HDD.

Blink

Indicates accessing the HDD.

Amber

Indicates HDD error.

Green/

Amber

Blink

Indicates HDD rebuilding.

N/A

Off

Indicates no HDD access or no HDD error.

Содержание R282-G30














































































































Результаты поиска

Содержание R282-G30

Отзывы:

Похожие инструкции для R282-G30

Бренды по названию

Популярные бренды

Gigabyte R282-G30, Руководство пользователя

Результаты поиска

Содержание R282-G30

Отзывы:

Похожие инструкции для R282-G30

Бренды по названию

Популярные бренды