Gigabyte R182-NA1 Скачать руководство пользователя

Страница: 60 / 107

- 60 -

BIOS Setup

5-2-5

USB Configuration

(Note) This item is present only if you attach USB devices.

Parameter

Description

USB Configuration

USB Devices:

Displays the USB devices connected to the system.

XHCI Hand-off

Enable/Disable the XHCI (USB 3.0) Hand-off support.
Options available: Enabled, Disabled. Default setting is

Enabled

USB Mass Storage Driver
Support

(Note)

Enable/Disable the USB Mass Storage Driver Support.
Options available: Enabled, Disabled. Default setting is

Enabled

Port 60/64 Emulation

Enables the I/O port 60h/64h emulation support. This should be
enabled for the complete USB Keyboard Legacy support for non-
USB aware OS.
Options available: Enabled, Disabled. Default setting is

Enabled

Содержание R182-NA1












































































































Результаты поиска

Содержание R182-NA1

Отзывы:

Похожие инструкции для R182-NA1

Бренды по названию

Популярные бренды

Gigabyte R182-NA1, Руководство пользователя

Результаты поиска

Содержание R182-NA1

Отзывы:

Похожие инструкции для R182-NA1

Бренды по названию

Популярные бренды