Gigabyte R182-M80 Скачать руководство пользователя страница 86

Страница: 86 / 109

- 86 -

BIOS Setup

5-3-7

PCH Configuration

Parameter

Description

PCH Configuration

PCH SATA Configuration

Press [Enter] to configure advanced items.

SATA Controller

– Enable/Disable SATA controller.

– Options available: Enable, Disable. Default setting is

Enable

Configure SATA as

–

Configures on chip SATA type.

– AHCI Mode: When set to AHCI, the SATA controller enables its AHCI

functionality. Then the RAID function is disabled and cannot be
access the RAID setup utility at boot time.

– RAID Mode: When set to RAID, the SATA controller enables both its

RAID and AHCI functions. You will be allowed to access the RAID
setup utility at boot time.

– Options available: AHCI, RAID. Default setting is

AHCI

Alternate Device ID on RAID

(Note 1)

– Enable/Disable Alternate Device ID on RAID mode.

– Options available: Enable, Disable. Default setting is

Disable

SATA Port 0/1/2/3/4/5/6/7

–

The category identifies SATA hard drives that are installed in the

computer. System will automatically detect HDD type.

(Note 1) Only appears when HDD sets to

RAID

Mode.

Содержание R182-M80














































































































Результаты поиска

Содержание R182-M80

Отзывы:

Похожие инструкции для R182-M80

Бренды по названию

Популярные бренды

Gigabyte R182-M80, Руководство пользователя

Результаты поиска

Содержание R182-M80

Отзывы:

Похожие инструкции для R182-M80

Бренды по названию

Популярные бренды