Gigabyte GA-946GM-DS2 Скачать руководство пользователя страница 38

Страница: 38 / 72

GA-946GM-DS2/S2 (rev. 2.0) Motherboard

- 38 -

English

Link Detected

Displays transmission speed

Cable Length

Displays the approximate length of the attached LAN cable

Note: The Gigabit hub will only operate at a speed of 10/100Mbps in MS-DOS mode; it will operate
at a normal speed of 10/100/1000Mbps in Windows mode or when the LAN Boot ROM is activated.

When a Cable Problem Occurs...

If a cable problem occurs on a specified pair of wires, the

Status

field will show

Short

and the

length shown will be the approximate distance to the fault or short.
Example:

Pair1-2 Status = Short / Length = 1.6m

Explanation: A fault or short might occur at about 1.6m on Pair 1-2.

Note: Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, their

Status

fields will

show

Open

, and the length shown is the approximate length of the attached LAN cable

Start detecting at Port.....
Link Detected --> 100Mbps
Cable Length= 30m

When LAN Cable Is Functioning Normally...

If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub,
the following message will appear:

OnBoard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled

Enable this function.

Disabled

Disable this function. (Default value)

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8/IRQ3.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8/IRQ3.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically setup the port 2 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8/IRQ4.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8/IRQ4.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8/IRQ3.

Disabled

Disable onboard Serial port 2.

Onboard Parallel Port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Содержание GA-946GM-DS2









































































Результаты поиска

Содержание GA-946GM-DS2

Отзывы:

Похожие инструкции для GA-946GM-DS2

Бренды по названию

Популярные бренды

Gigabyte GA-946GM-DS2, Руководство пользователя

Результаты поиска

Содержание GA-946GM-DS2

Отзывы:

Похожие инструкции для GA-946GM-DS2

Бренды по названию

Популярные бренды