Gigabyte GA-870A-USB3L Скачать руководство пользователя страница 24

Страница: 24 / 96

Hardware Installation

- 24 -

7) SATA3_0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by AMD SB850 South Bridge)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standards. Each SATA connector supports a single SATA device. The AMD SB850 south bridge

supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard

Drive(s)," for instructions on configuring a RAID array.

•

A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard

drives are to be used, the total number of hard drives must be an even number.

•

A RAID 5 configuration requires at least three hard drives. (The total number of hard drives

does not have to be an even number.)

•

A RAID 10 configuration requires four hard drives.

SATA3_0

SATA3_1

SATA3_4

SATA3_3

SATA3_5

SATA3_2

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

Please connect the L-shaped end of

the SATA cable to your SATA hard

drive.

Pin No.

Definition

GND

TXP

TXN

GND

RXN

RXP

GND

Содержание GA-870A-USB3L

































































































Результаты поиска

Содержание GA-870A-USB3L

Отзывы:

Похожие инструкции для GA-870A-USB3L

Бренды по названию

Популярные бренды

Gigabyte GA-870A-USB3L, Руководство пользователя

Результаты поиска

Содержание GA-870A-USB3L

Отзывы:

Похожие инструкции для GA-870A-USB3L

Бренды по названию

Популярные бренды