Gigabyte E152-ZE0 Скачать руководство пользователя страница 58

Страница: 58 / 138

BIOS Setup

- 58 -

5-2-6 Serial Port Console Redirection

(Note) Advanced items prompt when this item is defined.

Parameter

Description

COM1 Serial Over LAN

(Note))

Select whether to enable console redirection for specified device. Console

redirection enables the users to manage the system from a remote
location.
Options available: Enabled/Disabled. Default setting is

Disabled

COM1 Serial Over LAN
Console Redirection Settings

Press [Enter] to configure advanced items.

Please note that this item is configurable when COM1/Serial Over

LAN & COM2 Console Redirection is set to Enabled.

Terminal Type

– Selects a terminal type to be used for console redirection.

– Options available: VT100, VT100+, ANSI, VT-UTF8. Default setting

ANSI

Bits per second

– Selects the transfer rate for console redirection.

– Options available: 9600, 19200, 38400, 57600, 115200. Default

setting is

115200

Data Bits

– Selects the number of data bits used for console redirection.

– Options available: 7/8. Default setting is

Содержание E152-ZE0











































































































































Результаты поиска

Содержание E152-ZE0

Отзывы:

Бренды по названию

Популярные бренды

Gigabyte E152-ZE0, Руководство пользователя

Результаты поиска

Содержание E152-ZE0

Отзывы:

Бренды по названию

Популярные бренды