manualshive.com logo in svg

GIGA-TMS SmaFinger SF600, Быстрый старт

Поделиться
Скачать
GIGA-TMS SmaFinger SF600 Скачать руководство пользователя страница 7

TM951194 

7

2. Access Mode: Card Only 

Step 1 

In Standby mode the LED is blue on, you can read 

Manager Enroll Card to enter the enroll mode 

 

 

 

Step 2 

In enroll mode the LED is green blinking, you can read 

the User Card to store the card UID or Sector Data and 

enter the scan mode. 

Or read Manager Enroll Card again to exit the enroll 

mode. 

Step 3 

Read Manager Enroll Card to finish the enrollment and 

exit the enroll mode. 

Then the user's card can be used card-only on the 

SF600 enrolled.

   

Remark: 

1. Warning! Keep the User Card and do not lose it! To delete user must use the same User Card. 

Once you lose User Card, you cannot delete user from reader. 

2. The Multi-User Card cannot be used for Card Only access mode.

 

   

User’s Card 

Manager Card 

Standby 

 

Read Manager   

Enroll Card 

Scan Mode 

 

Read Card 

Read Manager Enroll Card   

to exit the enroll mode.   

Содержание SmaFinger SF600













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды