background image

1-5  Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

 

Make sure the motherboard supports the expansion card. Carefully read the manual that came 

with your expansion card.

 

Always turn off the computer and unplug the power cord from the power outlet before installing an 

expansion card to prevent hardware damage.

1-6  Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

DVI-D Port 

(Note)

The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60 Hz 

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-D 

connection to this port.

HDMI Port

The HDMI port is HDCP compliant and supports Dolby TrueHD and DTS HD 

Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM 

audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported 

resolution is 4096x2160@24 Hz, but the actual resolutions supported are dependent on the monitor 

being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The 

item name may differ depending on your operating system.)

(Note)  The DVI-D port does not support D-Sub connection by adapter.

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1.  Dual Channel mode cannot be enabled if only one memory module is installed.

2.  When enabling Dual Channel mode with two or four memory modules, it is recommended that memory 

of the same capacity, brand, speed, and chips be used. For optimum performance, when enabling 

Dual Channel mode with two memory modules, we recommend that you install them in the DDR4_1 

and DDR4_2 sockets.

Dual Channel Memory Configurations Table:

DDR4_4

DDR4_2

DDR4_3

DDR4_1

2 Modules

- -

DS/SS

- -

DS/SS

DS/SS

- -

DS/SS

- -

4 Modules

DS/SS

DS/SS

DS/SS

DS/SS

(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)

- 10 -

Содержание GA-AB350M-DS3H











































Отзывы: