manualshive.com logo in svg

GHS Corporation Rocktron Patchmate Loop & Floor, Руководство пользователя

Поделиться
Скачать
GHS Corporation Rocktron Patchmate Loop & Floor Скачать руководство пользователя страница 5

5

 PatchMate LOOP 8 Floor Top Panel

1   LOOP Switches

   

These switches are used to turn "on/off" each individual loop. The LED above each switch  will 

display the "current" status of the PatchMate.  If an LED above a switch is lit, that LOOP is ac-

tive.  If the LED above a switch is not lit, the LOOP is not active or off.

SECONDARY SWITCH FUNCTIONS

2  CHANNEL/BANK Function

   

In this function switches 1, 2, 3 and 4 are used to select the MIDI Channel and MIDI Controllers 

Banks.  This function is only accessable when turning "ON" the PatchMate LOOP 8 Floor.  See 

the section titled "SETUP YOUR PATCHMATE LOOP 8 FLOOR" later in this manual for the 

procedure.

3  PRESET DUMP Function

   

In this function switch 5 is used to dump presets from one PatchMate LOOP 8 Floor to another 

PatchMate LOOP 8 Floor.  This function is only accessable when turning "ON" the PatchMate 

LOOP 8 Floor.  See the section titled "PRESET DUMP" later in this manual for the proceedure.

4  CANCEL Function

   

In this function switch 6 is used to CANCEL any secondary function changes that you have 

made before you have stored them.

5  STEREO LINK Function

   

In this function switch 7 is used to select the STEREO LINK function whic allows you to link 

LOOPs within the PatchMate Loop 8 Floor for Stereo control. This function is only accessable 

when turning "ON" the PatchMate LOOP 8 Floor.  See the section titled "STEREO LINK" later 

in this manual for the procedure.

Содержание Rocktron Patchmate Loop & Floor

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды