manualshive.com logo in svg

GHS Corporation Rocktron Patchmate Loop & Floor, Руководство пользователя

Поделиться
Скачать
GHS Corporation Rocktron Patchmate Loop & Floor Скачать руководство пользователя страница 29

29

SETTING PatchMate USING MIDI PROGRAM CHANGES

Now that you have configured your PatchMate LOOP 8 Floor MIDI CHANNEL to the same channel as 

your midi controller along with enabling PROGRAM CHANGES ON, you are now ready to program 

your presets.

Make sure you have exited the MIDI CONFIGURATION PROGRAMMING MODE before using your 

PatchMate LOOP 8 Floor with a Midi Controller. 

1. Connect your Midi Controllers MIDI OUT to the PatchMate LOOP 8 Floor’s MIDI IN using a 5 PIN 

MIDI cord.

2. RECALL the desired preset you want to edit using your MIDI CONTROLLER.

3. Set the RELAY STATES using the front panel buttons.

4. Press STORE and release.

    The PatchMate LOOP 8 Floor will respond by blinking the STORE BUTTON one (1) time.

REPEAT STEPS 2-4 for all presets..... That’s it!

SMART LOOP CONTROLLERS

The PatchMate LOOP 8 Floor includes ROCKTRON’s exclusive Smart Controller Technology which 

allows the PatchMate LOOP 8 Floor to receive Latching or Momentary controller messages then apply-

ing user programmed release delay times.

This feature provides the user the ability to control Amplifiers that use momentary pulses to switch 

channels using latching or momentary midi continuous controller messages with a pre determined delay 

applied to the switch release. This delay value is determined by the reception of the on state value.

If the values received were 

 

 

 

127   = ON

 

 

 

0       = OFF

The relay operation will be executed immediately when received….. No delay will be applied….

However if the value for the on state is anything else other than 127 the following delay to release will 

be calculated using the following equation

 

 

 

[ ON VALUE * 2] * 1 millisecond

So if the value for on was 125 then the time the relay would be on for would become

 

 

[ 125 * 2 ] * 1 ms = 250 ms or about a Quarter of a Second. 

How to use an external MIDI Controller with the

PatchMate LOOP 8 Floor

Содержание Rocktron Patchmate Loop & Floor

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды