Ghost Controls Ghost Pro LSM1 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

background image

54

P U S H - T O - O P E N

PROGRAMMING THE OPEN LIMIT: PUSH-TO-OPEN

The

OPEN

limit is when the operator is extended and the gate is in the closed position.

IMPORTANT

ONLY THE OPERATOR ARMS’ EXTENDED LIMIT IS ADJUSTABLE AND CAN BE SET WITH THE CONTROL

BOARD. THE ARMS’ RETRACTED POSITION IS FIXED AND IS NOT ELECTRONICALLY ADJUSTABLE.
THE CLOSED POSITION IS SET BY HARDWARE MOUNTING ONLY. Please refer to the hardware installation to

make sure the retracted position is properly set/installed.

Installation Type

Retracted Position

Extended Position

Push-To-Open

Gate at the fully

CLOSED

position (not

electronically adjustable)

Gate at the

OPEN

position (electroni-

cally adjustable)

TURN THE CONTROL BOX ON

STEP 15.

Setting the open limit.

A. Press and hold the

JOG CLOSE

button on the gate system control board

until the gate reaches the

desired closed position. The gate can move

only if pressure is maintained. Releasing the

JOG

button will stop the

gate immediately.

B. Both

JOG

OPEN

or

JOG CLOSE

buttons are needed to ‘fine’ tune your

desired OPEN position.

STEP 16.

Press and hold the 1st set limit button on the control panel until it beeps, then release.

STEP 17.

Press the transmitter button to activate the gate and let the gate close fully you should

hear a single beep.

When the gate reaches its

CLOSED position, the control board will sound a single beep, confirming the CLOSED

limit has been set.

A.

Confirm the newly programmed OPEN limit by pressing the remote transmitter button to activate the gate and

confirm the closed position has been set correctly. This limit is stored and remembered even when all of the power

sources are removed.

B. Repeat STEPS 15-17 if needed to change your desired OPEN position.
C. Test your system with the remote transmitter to make sure it opens and closes without errors.

«
...
52
53
54
55
56
...
»

Содержание Ghost Pro LSM1





































































Отзывы:

Нет отзывов

Похожие инструкции для Ghost Pro LSM1

Бренд: Schlagel Страницы: 8

Бренд: CAME Страницы: 22

Бренд: DoorHan Страницы: 12

Бренд: Daspi Страницы: 12

Бренд: Beninca Страницы: 4

Бренд: Beninca Страницы: 11

Бренд: CAME Страницы: 36

Бренд: RIB Страницы: 56

Cardin Elettronica 100/SLX1524

Бренд: Riello Elettronica Страницы: 56

Бренд: GDS Страницы: 13

Бренд: Palfinger Страницы: 6

Бренд: Automatic Technology Страницы: 48

Бренд: Dea Страницы: 16

Бренд: fadini Страницы: 24

Бренд: tau Страницы: 35

Бренд: CAMDEN Страницы: 8

Бренд: Genie Страницы: 2

Бренд: Harbor Freight Tools Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды