manualshive.com logo in svg

Ghost Controls Ghost Pro LDM2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Ghost Controls Ghost Pro LDM2 Скачать руководство пользователя страница 55

55

P U S H - T O - O P E N

PROGRAMMING THE OPEN LIMIT: PUSH-TO-OPEN

The 

OPEN

 limit is when the operator is extended and the gate is in the closed position.

    IMPORTANT                                                                   

ONLY THE OPERATOR ARMS’ EXTENDED LIMIT IS ADJUSTABLE AND CAN BE SET WITH THE CONTROL 

BOARD. THE ARMS’ RETRACTED POSITION IS FIXED AND IS NOT ELECTRONICALLY ADJUSTABLE.
THE CLOSED POSITION IS SET BY HARDWARE MOUNTING ONLY. Please refer to the hardware installation to 

make sure the retracted position is properly set/installed.

Installation Type

Retracted Position

Extended Position

Push-To-Open

Gate at the fully 

CLOSED

 position (not 

electronically adjustable)

Gate at the 

OPEN

 position (electroni-

cally adjustable)

TURN THE CONTROL BOX ON

STEP 18. 

Setting the open limit.

A. Locate the 2nd SET limit settings on the control board and press and 

hold the 

JOG CLOSE

 button for the second gate until the gate 

reaches the 

desired closed position. The gate can move only if  

pressure is maintained. Releasing the 

JOG 

button will stop the  

gate immediately.  Once the 2nd set is in the desired closed position  

then repeat for  

the 1st gate with the 

1st SET limit settings 

JOG CLOSE

 button. 

B. Both 

JOG

 

OPEN

 or 

JOG CLOSE 

buttons are needed to ‘fine’ tune your 

desired OPEN position.

STEP 19.

 Press and hold the 1st set limit button on the control panel until it beeps, then release.  

Then Press and hold the 2nd set limit button until it beeps, then release 

STEP 20.

 Press the transmitter button to activate the gates and let the gate close fully you should 

hear a single beep. 

 

When the gate reaches its 

CLOSED position, the control board will sound a single beep, confirming the CLOSED  

 

limit has been set.

A.

   Confirm the newly programmed OPEN limit by pressing the remote transmitter button to activate the gate and confirm 

the closed position has been set correctly. This limit is stored and remembered even when all of the power sources are 

removed.

 

B.  Repeat STEPS 16-18 if needed to change your desired OPEN position.
C.  Test your system with the remote transmitter to make sure it opens and closes without errors.

2ND SET LIMIT SETTINGS

1ST SET LIMIT SETTINGS

Содержание Ghost Pro LDM2




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды