Ghost Controls Ghost Pro LDM2 Скачать руководство пользователя страница 37

Страница: 37 / 67

P U L L - T O - O P E N

2 0 2 0

CONNECTING SOLAR TO YOUR SYSTEM

STEP 22.

Adding a solar panel to the control box. Turn your system off.

A. When wiring a Solar Panel you will need to insert the solar wires into the SOLAR SCREW TERMINALS

which are located on the PWR INPUT section of the main control board. Once inserted then tighten each

screw so that the wires do not come loose and fall out. Please refer to diagram below.

DO NOT CONNECT

AC TRANSFORMER IF USING SOLAR POWER.

DO NOT USE this terminal

if using Solar Panel

Black

Red

Battery Harness

Operator Arm

Connect the Solar Wire’s to the

control board “Solar” terminals.

Connect the red wire to the

positive (+) “SOLAR” terminal

and the black wire connects to

the negative (-) “Solar” terminal

on the control board.

B. Turn the system on. Check that green LED (Power

status) on top center of control board is on.

This indicates that the battery is being charged.

C. Check the chart shown for number of hours of direct

sunlight available for solar applications.

D. Determine the number of expected winter cycles for a

single gate using solar power by reviewing the map and

chart shown.

A MAXIMUM OF 3 AXDP 10-WATT SOLAR PANELS OR ONE AX30

PANEL (NO MORE THAN 30 WATTS IN TOTAL) POWER SHOULD BE

CONNECTED TO ANY GHOST CONTROLS SYSTEM CONTROL

BOARD.

Содержание Ghost Pro LDM2




































































Результаты поиска

Содержание Ghost Pro LDM2

Отзывы:

Бренды по названию

Популярные бренды

Ghost Controls Ghost Pro LDM2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Ghost Pro LDM2

Отзывы:

Бренды по названию

Популярные бренды