background image

 

 

1

 

General safety information 

Specified normal use 
The drive unit is intended for sectional doors with full counter-balancing. 
The safe operation is only guaranteed with normal specified use. The drive unit is to be 
protected from rain, moisture and aggressive ambient conditions. No liability for damage 
caused by other applications or non-observance of the information in the manual. 
Modifications are only permitted with the agreement of the manufacturer. Otherwise the 
Manufacturer’s Declaration shall be rendered null and void. 
 
Safety information 
Installation and initial operation tasks are to be performed by trained, skilled fitters only. 
Only trained electrical craftsmen are permitted to work on electrical equipment. They must 
assess the tasks assigned to them, recognise potential danger zones and be able to take 
appropriate safety measures. 
The installation is only to be carried out with the supply off. 
Observe the applicable regulations and standards. 
 
Coverings and safety devices 
Do not operate unless corresponding coverings and safety devices are fitted/installed. 
Ensure that gaskets are correctly positioned and cable glands are correctly tightened. 
 
Spare parts 
Use only original spare parts. 

 

 

 

Содержание ELEKTROMAT SE 15.48-25,40





















Отзывы: