GESTRA LRS 1-7 Скачать руководство пользователя

Страница: 22 / 24

Decommissioning

Exchanging the conductivity switch

1. Switch off mains voltage.
2. Undo cover screws

and remove the housing cover

(Fig. 2, 3)

3. Detach mains and control cables from terminal strips

and pull lines out of the cable glands.

4.  Detach connecting line to conductivity electrode.
5.  Remove conductivity switch.
6.  Install and connect new conductivity switch.
7.  Attach connecting line to conductivity electrode.
8.  Apply mains voltage.

Danger

The terminal strips of the conductivity switch LRS 1-7 are live during operation.

This presents the risk of severe cases of electric shock!

Always

cut off power supply

to the equipment before mounting, removing or connecting

the terminal strips!

Disposal

Dismantle the conductivity switch and separate the waste materials, using the material specification

as a reference. Electronic component parts such as the circuit board must be disposed of separately!

For the disposal of the conductivity switch observe the pertinent legal regulations concerning waste

disposal.

Содержание LRS 1-7

























Результаты поиска

Содержание LRS 1-7

Отзывы:

Похожие инструкции для LRS 1-7

Бренды по названию

Популярные бренды

GESTRA LRS 1-7, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LRS 1-7

Отзывы:

Похожие инструкции для LRS 1-7

Бренды по названию

Популярные бренды