GB
GB-2
OPERATING AND
STARTING GUIDE
Fine Sand Filter
If you use water containing
fine sand we recommend that
you mount a fine sand filter.
The filter element is changed
as required.
If a fine sand filter is not
mounted there is a risk that
the fine sand will deposit in the
by-pass valve which may
result in damage to the by-
pass valve, top section and
Turbo Laser, and this is not
covered by the warranty.
High pressure hose
Your new high pressure clea-
ner is provided with a heavy
high pressure hose. Do not
attempt to pull the high pres-
sure hose when moving the
high pressure cleaner. Be
careful not to run over or in
any other way damage the
high pressure hose. The war-
ranty does not cover broken
hoses or hoses which have
been run over.
Turbo Laser
The high pressure cleaner is
also provided with a Turbo
Laser nozzle for highly impro-
ved cleaning efficiency (see
“Technical Data”).
Starting
Study carefully the safety
instructions in the “operation
manual HONDA GX 390
(600X) / HONDA GX 140
(118P)”. Also observe the
periodic maintenance of the
petrol engine. The maximum
RPM of the engine is fixed
from the factory and must not
be altered.
1. Fill the tank (2.19) with
fresh automobile petrol
(lead-free is fine).
2. Check the oil level in the
engine and refill when
necessary with SAE
10W/30 or SAE 10W/40
motor oil. The oil is just to
touch the oil rod (2.18).
3. Check the oil level of the
pump. The level should
only be read at stand-still.
The oil should reach the
“MAX” mark on the oil rod
(2.17) (600 PX) / the oil
must be at the indication
"oil level" on the oil glass
(118P). Refill with “HYPOID
80W/90” oil in the oil glass.
The water supply hose is
flushed through before it is
connected to the high pres-
sure cleaner. Hose diame-
ter is minimum 3/4”.
The water supply pressure
must not exceed 10 bar
during operation.
4. Mount the high pressure
hose (2.6) to the pressure
outlet (2.5).
5. Turn the petrol cock (2.24)
to the extreme right and
turn the ignition switch to
“ON”.
6. Turn the choke (2.23) to the
extreme left.
7. Turn the throttle (2.22) a litt-
le to the left.
8. Pull the start cord (2.21) out
in one long pull and let it
return slowly. While the
machine is warming up the
choke handle is gradually
turned to the right. Then,
the throttle is turned to the
extreme left. Open the
pressure regulation handle
(2.9) and activate the pistol
(2.7). Let the machine run
until constant pressure is
achieved.
The machine is now ready for
operation. By means of the
pressure regulation handle the
pressure may be adjusted infi-
nitely variable up to the machi-
ne’s maximum pressure rate.
Stop
Turn the throttle (2.22) to the
extreme right. Turn the ignition
switch (2.21) to pos. “OFF”
and turn the petrol handle
(2.19) to the extreme left.
If the machine has been out of
operation for quite a long time
- see the "Operation manual
HONDA GX 390 (600 PX) /
HONDA GX 140 (118P)".
Detergent Application
(600 PX)
When the pressure regulation
handle (2.9) is open (turned
anti-clockwise) detergent may
be applied via the detergent
valve (2.14). For maximum
supply of detergent - see
Technical Data.
The detergent valve must be
closed when detergent is not
being used as the pump may
otherwise draw air.
2.4
2.10
2.17
2.15
2.14
2.13
2.5
2.16
2.2
2.1
2.3
2.6
2.8
2.9
2.7
2.19
2.1
2.3/4
2.6
2.8
2.9
2.7
2.
15/17
2.10
2.18
2.5
2.22
2.23
2.19
2.21
2.20
2.20
2.18
2.21
2.24
