Notice for Operation
P.9
Operating Instructions
P.8
Power-up Mode (Energy-saving Mode)
When the unit is connected to the power, only the red indicator light
will be on (blinking) while other
indicators and LCD display remain off. The unit switches to energy-saving mode after the buzzer beeps for
a second. Under the standby mode, the unit will automatically switch to energy-saving mode if left idle for 3
minutes. Under this situation, the red “ON/OFF” indicator will blink while the LCD display and other indicators
remain off. Press the “ON/OFF” button to enter standby mode.
Standby Mode
LCD display will indicate time as “TIME 00” and speed as “SPEED 1”; the “ON/OFF” indicator will light up in
red and other indicators in blue. The unit will automatically switch to standby mode after the completion of any
working programme. The unit will enter power-up mode after rebooting from a power failure.
Custom Mode:
Under standby mode, set the time and speed, press “RUN/STOP” button to start operating the unit, blue light on
the “RUN/STOP” indicator flashes. When it needs to be stopped, press the “RUN/STOP” button again. After the
unit stops working, it automatically turns back to standby mode and blue light on “RUN/STOP” indicator flashes.
Note: In the custom mode, when finish setting time and speed, before pressing “RUN/STOP” button, if you press
the preset programme button VEGETABLES or PULSE, the corresponding working mode starts and the time and
speed setting become invalid.
Time display
: the value of time display increases or decreases by every minute, for example:
If the preset working time is 5 minutes, the time indicator displays 5. if it operates for a few time but not exceed
1 minute, time display stays at 5; if it operated for more than 1 minute but less than 2 minutes, it displays 4,
the rest can be display in the same manner. If time is adjusted during operation, the preset time will increase
or decrease basing on the original working time on the screen, the unit will fix the operation according to the
adjusted time. For example, if the preset time is 5 minutes, press button to increase 1 minute to 6 minutes, the
unit will restart to work for 6 minutes; if you press button to decrease 1 minute, the time indicator displays 4, the
unit will restart to work for 4 minutes.
-
Insert the measuring cup to the lid (align the two bumps on the measuring cup to the two grooves on the lid and
turn anti-clockwise to position). Then press down the lid of the blender jar to close. To open, pull up by the flap of the lid.
- The seal ring is detachable from the lid for easy cleaning. Remove seal ring from the lid after use to thoroughly clean the
lid and rinse off food residue from seal ring.
Measuring Cup, Lid and Seal Ring
- The appliance will not start operation until the blender jar is placed onto the unit base for safety purpose.
- Insert the measuring cup to the lid (align the arrow on the cup to the symbol on the lid and turn it to
position). Then press down the lid to the blender jar to close. To open, pull up by the flap of the lid.
- During operation, close the lid tightly to avoid injuries due to spilling or splashing of hot liquids.
- Wind excess power cord underneath the unit base to prevent the rubber foot from stepping on the power cord.
- When the food is too thick or there is too little liquid in the jar, the motor will be dragged to a low speed or stop
to operate. Hence, when blending thick and sticky food, start blending from low to high speed. If it is still unable
to blend, disconnect the power and stir the food inside the jar using a rubber stirrer to drive out the air trapped
in food. Then close the lid and switch on the blender to continue the operation.
- When overheating is sensed, the temperature monitoring system will be activated and would stop the operation
of the motor. In this case, put the appliance in a place with good ventilation to cool down for 45 minutes. The
system will be reset and you may resume the operation of the appliance.
- Keep hands and utensils out of the jar while the motor is running to prevent the possibility of severe personal
injury and/or damage.
- When making hot beverages or soups (such as soy milk, porridge, bisque, etc.), please ensure the lid is secured
tightly to the jar to prevent it from falling. Please be advised to start the operation at low speed first and then
gradually increase the speed, or simply use the “Pulse” mode.
- When making sauces (eg. almond sauce, jam and sesame sauce), stuffing and nuts, put in around 2 to 3 cups
of ingredients. The amount should neither be too much or too little. Keep the blending time within 2 min to
prevent any burnt smell due to overheating. Too much ingredients may lead to overloading and overheating of
the motor. In this case, wait till the motor temperature drops before operating again.
- Please put liquid and soft food into the jar before putting in hard food or ice cubes.
- When the operation finishes, please wait until the blade assembly comes to a complete stop before taking out
the blender jar.
- If you smell a burnt smell from the blender, stop operation immediately. It may be caused by the abrasion of
the rubber cushion base if it is not properly assembled.
- Do not operate continuously for over 10 minutes each time.
