manualshive.com logo in svg

GeoVision GV-POE1611-V2, Руководство пользователя

Поделиться
Скачать
GeoVision GV-POE1611-V2 Скачать руководство пользователя страница 29

 

Configuration

 

 

6 

 

6.11  Power over Ethernet 

PoE technology is a system to pass electrical power safely, along with data, on Ethernet 
cabling. Power is supplied in common mode over two or more of the differential pairs of sires 
found in the Ethernet cables and comes from a power supply within a PoE enabled 
networking devise such as Switch or can be injected into a cable run with a midspan power 
supply. 
 
This figure shows all the PoE status when connect or disconnect to the PD device. 

 

    Figure 6-15 

 

 

PoE Enabled: 

POE of the port is able to supply power to the attached PD (Powered 

Device) 

 

PD Class:

 Detects the class of PD. 

 

Delivering Power (W): 

Output power.   

 

Total Power:

 Total watts that has been used. 

 

Note: 

The green columns show the status of the connected PD. To protect the system 

and better product life, configure the Total Power to be lower than 80% of maximum 
power consumption. 

 

25

Содержание GV-POE1611-V2












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды