Geosense VWNPC-3000 Скачать руководство пользователя страница 11

Страница: 11 / 30

V1.4 March 15

It is VITAL that personnel responsible for the installation and

use of the NATM cells READ and UNDERSTAND the manual,

prior to working with the equipment.

**********

As stated before, it is vital to check all the equipment in the shipment soon after

taking delivery and well before installation is to be carried out. Check that all

components that are detailed on the shipping documents are included.

5.0

INSTALLATION

This section of the manual is intended for all users of

Geosense

NPC

3000 NATM

Cells

and is intended to provide guidance with respect to their installation.

It must be remembered that no two installations will be the same and it is inevitable

that some

‘

fine tuning

’

of the following procedures will be required to suit specific site

conditions.

5.1.2 Tangential cell (VWNPC

3000)

Typical installation is by using short

pieces of steel rebar grouted inside short

boreholes and protruding into the area where

the lining will be placed.

STEP 1

place a

VWNPC

3000

tangential

stress cell onto two horizontal re

bar mountings.

STEP 2

carefully bend the pressure tube 90

degrees away from the tunnel wall so that it

protrudes through the shotcrete lining and can

be accessed for re

pressurising.

STEP 3

tie to the re

bars using soft iron wire

connected to the lugs at the corners of the cell.

5.1 Cell Installation

Cells are positioned on the wall of the tunnel in two ways, one way to monitor

tangential

stresses and the other to measure

radial

stresses.

CELL MUST BE INSTALLED

PERPENDICULAR TO TUNNEL

LINING

Содержание VWNPC-3000































Результаты поиска

Содержание VWNPC-3000

Отзывы:

Бренды по названию

Популярные бренды

Geosense VWNPC-3000, Инструкция по эксплуатации

Результаты поиска

Содержание VWNPC-3000

Отзывы:

Бренды по названию

Популярные бренды